OEM Dremel Scroll Saw Parts & Accessories

Bellows

$4.99

Fix Number: FIX10260640
Manufacturer Part Number: 2615302998

This is an authentic OEM part that has been sourced directly from Dremel. The bellows connects the dust blower tube to the scroll saw; it provides a strong blast of air that helps keep your work surface clean. The bellows is part of the dust blowing mechanism, they draw the saw dust away from the blade and allows for better visibility while operating the tool. When your bellow has become brittle, damaged, or cracked it allows air to leak out and become less effective. This bellows is sold individually. Before attempting to replace your bellow make sure you unplug your scroll saw.

Installation Instructions

Jordan from RALEIGH, NC

Original rubber bellow was dried and cracked (no seal)

Remove two screws from the oval plate covering the bellow, located behind the speed adjustment knob. If the air hose is attached to the side of the housing of the top arm, you may want to unscrew that too. Next, carefully pull the bellow fixture from the housing and detach the clear tubing to the air hose. Don’t pull hard; there is not much slack. Remove the rubber bellow from the hard plastic mount and replace with the new bellow. It’s a tight fit—install the new bellow with care, making sure not to tear or pinch it. Reattach the tubing to the air hose and place the bellow fixture back into the housing. Put the oval cover back in place and screw everything back together. Read more...

Brush and Spring Pair

$8.35

★★★★★

1 Review

Fix Number: FIX10260545
Manufacturer Part Number: 2615296770

This is an authentic OEM part that has been sourced directly from Dremel. This carbon brush and spring pair is found on the outside of the motor assembly on your scroll saw. Carbon brushes help power the saw by helping transferring electricity from a stationary part to a rotating part in a motor. Helping drive the motor means these brushes face a lot of friction and heat, therefore they will wear down over time and need to be replaced. Before attempting to replace the carbon brush make sure you have unplugged the scroll saw.

Bearing Seat Assly

$25.66

Fix Number: FIX10260633
Manufacturer Part Number: 2615302973

Switch Plate

$8.35

Fix Number: FIX10260150
Manufacturer Part Number: 2610913479

Angle Attachment

$8.35

Fix Number: FIX10260059
Manufacturer Part Number: 2610031628

Installation Instructions

Dwayne from Las Vegas, NV

small thin cuts with minimal waste with accuracy

the table is OK and allows for 1/4"x1/4"x1.5" thin cuts for saddles and nuts for acoustics if two adjustable guides are used as a fence, saddles ae 1/8th" x 3/8ths" x 2.5" .. the wooly mammoth is too precious to use a thick blade so the dremel is the best bet and as thin as you can get..

however there is no attachment that comes with that allows me to make these cuts extremely accurate, so I use a 90 degree blade, use TWO of the guides I bought from Fix, then I turn them so each are a straight line, much like a fence on a table saw, WORKS GREAT! adjustable with thumb screws, and I can set whatever depth I need.

this is a no muss no fuss simple solution for the desired outcome.. thin blade means minimal waste and minimal sanding ..

the price of two guides are what $14 or so? they fit nice and beat trying to clamp up some bukly C clamp jobbie with a steel or wood fence..

if I could post up an image or a video I could show how I tackled it, this solution won't pop in most folks head as its very unconventional but once you see it you will think, ah yes this is what those guide rails and 90 degree blades are for... WORKS, if you need a fence, just think perpendicular to the normal blade set up, the 90 degree blades tae care fo the direction..

so if you clamp the scroll saw to a table whatever and face it, the adjustable fence and cuts aren't front to back, they are left to right or side to side.. and they must have made these just for this cuz when you install two of the guides and spin them they almost touch..

I dont think thats accidental or coincidence, if you see the set up its all makes sense, this should be included in dremels instructions but its not, it solves so many problems of making exact straight line cuts that are thin and need to be very accurate..

most use a scroll saw for scroll cuts not straight, but someone thought to put fence rails on each side and then make the guides as an accessory, very clever whoever this was..

TY, Dee Read more...