OEM DeWALT Orbital or Palm Sander Parts & Accessories

Carbon Brush

$6.51

Fix Number: FIX10188358
Manufacturer Part Number: N097696

Genuine Dewalt replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Brush Box Asm

$6.51

Fix Number: FIX12522639
Manufacturer Part Number: N292059

This is a brush box assembly designed for various sander models. Brush boxes are essential components that house carbon brushes responsible for transferring electricity from the motor to the sanding pad. When the carbon brush assembly wears out, it can no longer efficiently transfer electricity, causing the sander to stop working. This brush box assembly includes the carbon brush, its housing, and the necessary wiring. Replacing the brush box assembly is a straightforward process, requiring only a screwdriver and a set of pliers. Begin by disconnecting your sander from its power source, whether it is a battery or a wall outlet. Next, remove the screws securing the main housing of the sander and locate the brushes inside. Use a set of pliers to disconnect the wire from the old brush and a flat-head screwdriver to lift the old brush out of its slot. Insert the new brush box assembly into the slot and connect its wires. Finally, reattach the sander outer housing and secure it with the screws.

Sander Base Plate

$45.40

Fix Number: FIX12533027
Manufacturer Part Number: N329079

This genuine OEM pad assembly—also known as a hook-and-loop sanding pad or sanding disc—is designed for use with compatible sanders and sourced directly from the original manufacturer. The circular pad measures 4.75 inches in diameter, features 8 dust extraction holes, and includes a Velcro backing to securely hold sandpaper discs in place during operation. Mounted to the base of the sander, this pad allows for smooth, efficient sanding and consistent surface finishing. Over time, the Velcro surface may wear down, or the pad may become cracked or stripped, leading to poor sandpaper grip, uneven sanding, or reduced performance. Replacing the pad is a simple repair that requires no specialized tools. To install, use a screwdriver to remove the retaining screws from the old pad. Align the new pad assembly with the mounting holes and secure it using the original or replacement screws. It’s recommended to inspect and replace any stripped or corroded screws during installation for best results. This part is sold individually and is ideal for restoring your sander’s performance and extending its service life.

PAD

$39.83

Fix Number: FIX12398026
Manufacturer Part Number: 151281-08

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

Belt

$7.86

Fix Number: FIX12529381
Manufacturer Part Number: N430442

This part includes a single belt for a random orbital sander. It is located between the pad and the sander body. It helps to control the pad speed while the tool is off the work surface. The belt is a common wear part that will require replacement from time to time (along with the pad, which is sold separately). The belt should be replaced when the pad speed increase significantly when the unit is removed from the work piece. For this repair, remove the screws holding the pad in place, remove the pad, replace the damaged belt by wrapping it around the shoulder screw and bearing retainer. Reinstall the pad and re-tighten the screws, being careful not to over-tighten them.

Watch the install video

BRUSH

$12.35

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Cord Protector

$6.51

Fix Number: FIX17061542
Manufacturer Part Number: N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Watch the install video

Sander Pad & Backing Plate

$9.55

★★★★★

1 Review

Fix Number: FIX10166489
Manufacturer Part Number: 151284-00SV

This is an OEM sander pad and backing plate for a sander. It is most commonly replaced due to sudden uneven sanding or difficulty keeping the sandpaper properly attached. This part includes a steel plate with a foam pad fixed to it. The foam pad gives grip for the sandpaper to adhere firmly within the clamps. This foam material is prone to deteriorate over time, causing irregular sanding. If the pad is so worn that the metal plate is making contact with the paper, the sander will start to jump around. This is a very quick and easy repair. Simply remove the four screws holding the old pad in place, line up the the holes of the pad with the holes in the plate, and tighten the four screws back up (screws sold separately).

Pad Assembly (psa)

$23.07

Fix Number: FIX12525699
Manufacturer Part Number: N373679

This is a single pad assembly for a random orbit sander. The pad assembly holds the sand paper in place and creates a level surface needed for sanding. Pads are prone to wear and tare over time and will need to be replaced when they do. It will start to deteriorate around the edge. To prolong the life of your pad assembly do not apply too much pressure to the pad while sanding. This simple repair should only take a few minutes to complete.

On-off Switch

$6.51

★★★★★

1 Review

Fix Number: FIX10166039
Manufacturer Part Number: 144960-00

This part includes one on-off switch, also referred to as a rocker switch. This switch is an original manufacturer replacement part. The switch controls the flow of electricity to the motor, and when it wears it can make it impossible to start the power tool. Switches are a common replacement part for power tools, so it is something that should be inspected as part of your regular maintenance. This black switch has two terminals and a compact design for an uncomplicated installation process. To confirm that the switch is damaged, you can test it for continuity using a multimeter.

DeWALT Orbital or Palm Sander Parts

Popular DeWALT Orbital or Palm Sander Parts

DeWALT Orbital or Palm Sander Appliance Types

Popular DeWALT Orbital or Palm Sander Models

DeWALT Orbital or Palm Sander Parts

Start With Your Model Number

Popular DeWALT Orbital or Palm Sander Parts

DeWALT Orbital or Palm Sander Appliance Types

Popular DeWALT Orbital or Palm Sander Models