OEM Black and Decker Hammer Drill Parts & Accessories

Cap

$6.51

Fix Number: FIX10169009
Manufacturer Part Number: 323489-00

This is a genuine part which is supplied by the original equipment manufacturer for use with DeWALT and Black and Decker rotary hammers. The cap provides cushioning for the chuck. If the component is worn, damaged or missing, this will provide an identical replacement for the original cap that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and the correct repair procedure. Keep in mind it is sold as an individual item.

Chuck Key

$13.58

Fix Number: FIX10169759
Manufacturer Part Number: 330034-03

This is an authentic manufacturer sourced replacement part designed for use with drills. This chuck key tightens and loosens the jaws of the chuck. This item is made out of metal and it is sold individually.

Watch the install video

Retaining Ring

$6.51

Fix Number: FIX10166028
Manufacturer Part Number: 144803-00

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

Roller

$8.47

Fix Number: FIX10169225
Manufacturer Part Number: 325878-00

This is an authentic replacement part manufactured for use with rotary hammers and demolition hammers. The special roller is used to reduce friction between the spindle and the casting. This roller is available as an individual replacement part, please note two rollers are required.

Washer

$6.55

Fix Number: FIX10179826
Manufacturer Part Number: 578387-00

This is an authentic replacement part used in rotary hammers. The metal washer is used for spacing for the cylinder assembly, and protects the tube from wear. This washer is sold individually, please see model diagram for any additional parts.

BRUSH

$6.51

Fix Number: FIX18988070
Manufacturer Part Number: 90512443

+óGé¼-ó Worn brushes are often the cause of a poorly running motor +óGé¼-ó Replacing brushes can fix an intermittent motor +óGé¼-ó New brushes can restore a motor+óGé¼Gäós electric braking Carbon motor brushes are one of the most commonly replaced power tool components.+é • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement.+é • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power.+é • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned.+é • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

O Ring

$6.51

Fix Number: FIX10165223
Manufacturer Part Number: 049787-00

It is a high-quality component which is supplied by the original equipment manufacturer for use with Dewalt and Black and Decker power tools. This replacement o-ring has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. It is made of durable rubber material and it is sold individually.

Ball

$6.51

Fix Number: FIX10180184
Manufacturer Part Number: 583890-00

This is an authentic OEM part. The metal ball from DeWALT is used in rotary hammer drills. It is designed to hold the drill bit in place, and fits inside the spindle. A screwdriver may be needed to replace the part. Please refer to the owner's manual and the diagram of your specific model for proper installation. This item is individually priced.

Watch the install video

Power Cord

$23.86

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Electric Drill Cord Protector

$9.74

Fix Number: FIX10169655
Manufacturer Part Number: 330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Black and Decker Hammer Drill Parts

Popular Black and Decker Hammer Drill Parts

Installation Instructions

Installation Instructions

Black and Decker Hammer Drill Appliance Types

Related Black and Decker Hammer Drill Parts

Popular Black and Decker Hammer Drill Models

Black and Decker Hammer Drill Parts

Start With Your Model Number

Popular Black and Decker Hammer Drill Parts

Installation Instructions

Installation Instructions

Black and Decker Hammer Drill Appliance Types

Related Black and Decker Hammer Drill Parts

Popular Black and Decker Hammer Drill Models