Black and Decker Hammer Drill Power Cords

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Fix Number

FIX10169655

Manufacturer Part Number

330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Fix Number

FIX10169973

Manufacturer Part Number

36480-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 10 Feet Long

Fix Number

FIX10169976

Manufacturer Part Number

36495-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 16 Gauge • 15 Feet Long

Fix Number

FIX10173549

Manufacturer Part Number

448557-98

This replacement 10 foot power cord is specially produced for Black and Decker and Dewalt power tools. It is designed to connect to a standard US outlet supplying power to the tool. Please note one rubber insulated cord is included per order, the cord protector is not included it is sold separately. To complete this repair you will need a screwdriver.

Fix Number

FIX10168984

Manufacturer Part Number

323091-01

This rubber piece is a genuine OEM part manufactured for DeWALT and Black & Decker. It is sold individually. A cord protector attaches at the point of connection between cord and power tool. It protects cord and wires from damage caused by stress, strain, and motion. This repair is fairly simple and requires just a screwdriver. A damaged cord must be replaced as well. Replacement cords are sold separately. • Unplug power tool • Remove the casing • Detach wires from tool • Slide cord protector onto cord • Reattach wires and casing • Test power tool

Fix Number

FIX10169879

Manufacturer Part Number

330073-98

This replacement power cord is a genuine OEM sourced item that is specially designed for use with Black and Decker and Dewalt power tools. Its purpose is to supply electricity from a standard U.S. outlet to the tool. This high quality rubber insulated cord is included per order, please note the cord protector is not included, it is sold separately.

Fix Number

FIX10169900

Manufacturer Part Number

330076-20

This is a genuine part which is supplied directly by the original equipment manufacturer and is used with Dewalt and Black and Decker rotary hammer drills. When plugged in, the power cord transfers power to the unit. This part is made of flexible plastic and metal, it is also sold individually. For installation, you will need a screwdriver, and a pair of needle nose pliers to aid you.

Fix Number

FIX10184444

Manufacturer Part Number

770235

This replacement cord protector is an authentic component which is supplied by the original equipment manufacturer for use with DeWALT and Black and Decker power tools. It fits through the opening in the housing where the power cord is wired, it will protect the base of the cord from getting bent or pinched. It is made of high-quality rubber material and it is sold individually.

Fix Number

FIX10183098

Manufacturer Part Number

637678-00

This is an OEM part sourced directly from the manufacturer. The Cord protector is used in Black & Decker drills to guard the connection between the cord and the drill. It also provides a place to store the chuck key. This part is made of semi-flexible rubber, and is sold individually. You may require a flat-head screwdriver to pry the old part free, and then the new part can be slotted into place.