Washer Valves

Fix Number

FIX12348013

Manufacturer Part Number

W11165546

If your washer isn’t filling properly or is leaking near the back, this inlet valve might be the problem. It controls how hot and cold water enter your machine during the wash cycle. With two inlets and three push-on connectors, it’s easy to install using a screwdriver and wrench. Just make sure to unplug your washer and turn off the water first. This part fits many models—check yours to be sure it’s the right match.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX3527427

Manufacturer Part Number

5220FR2006H

The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with water at all. If this happens the valve should be replaced. There are a couple different methods for testing if your hot water valve is defective. The first is to use a multimeter on the solenoid, the second is to unplug the washer while it is running. If water continues to flow into the machine, then the valve is defective. This genuine OEM part has a standard hose fitting inlet, one water outlet, and measure approximately 3 inches long by 3 inches wide. To complete this repair, you will need to disconnect the water and power supply to your washer and pull it out from the wall so you can access the back panel.

★★★★★

★★★★★

1 Review

Fix Number

FIX12374721

Manufacturer Part Number

AJU75152601

This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.

Fix Number

FIX11728995

Manufacturer Part Number

5220FR2075L

If your washing machine is leaking, slow to fill, will not stop filling with water, or is not filling at all, the cold-water inlet valve may be defective. The purpose of the valve is to open to allow water into the washer, and is used for cold water, liquid bleach, and prewash cycles in your washing machine. This is a genuine OEM replacement part that measures approximately 4 inches long and 3 inches wide. It has a standard hose fitting inlet along with two outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left. When replacing this part, you will want to disconnect the power and water to your washer and remove the fill hoses. You will need to pull the machine out far enough so that you are able to access the back panel where the valves are located.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334646

Manufacturer Part Number

285805

There are many symptoms that may indicate an issue with your water inlet valve. These can include your washer not filling with water, it will not stop filling, the washer is leaking, or it is both filling and draining at the same time. You can test if your valve is faulty two different ways. The first is to disconnect the power while the washer fills, if water continues to fill the tub, then the valve should be replaced. The second way is to use a multimeter to test for continuity on the valve solenoids. If you do need to replace the water inlet valve, this is a genuine OEM part that has two ports and is compatible with half-inch ID hose. Before beginning your repair, please be sure to disconnect the power and water supply to your washing machine.

★★★★★

★★★★★

1 Review

Fix Number

FIX12349267

Manufacturer Part Number

W11210459

If your washer is leaking, will not fill with water, or will not stop filling, there may be an issue with your water inlet valve. This part is used to control the flow of hot and cold water into the washer. If there is reduced water flow, first check if the screens on the valve are blocked with debris. A multimeter can be used to test if the valve is faulty or not. Please be sure to disconnect both the power and water supply to your washer before replacing the valve.

★★★★★

★★★★★

1 Review

Fix Number

FIX12726769

Manufacturer Part Number

WH13X26535

This replacement water inlet valve ensures accurate control of hot and cold water entering your washing machine. It plays a key role in maintaining proper water levels for each cycle. If your washer won’t fill, leaks, or fills unexpectedly, the valve may need to be replaced. The assembly is gray, encased in plastic, and does not include a gasket. Installation requires basic tools and should be performed with the appliance unplugged and water supply turned off.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX11749042

Manufacturer Part Number

WPW10144820

This part is used to help control and balance the water temperature flowing in to the washer tub.

Fix Number

FIX12349461

Manufacturer Part Number

W11220230

The water inlet valve plays a crucial role in your washing machine’s operation by controlling the flow of hot and cold water into the tub. If the valve is damaged or worn out, you may experience slow filling, no water at all, or leaks beneath the appliance. This OEM replacement features dual inlets and is designed for a secure fit. To install, you’ll need basic tools to access and remove the old valve. Once replaced, your washer should return to normal water flow and performance.

Fix Number

FIX16544354

Manufacturer Part Number

5304528029

This OEM water inlet valve assembly with flow meter fits select Frigidaire, Electrolux, White Westinghouse, and Tappan washers. It regulates water flow for efficient operation and energy savings. Unplug the washer and shut off the water supply before installing. Refer to your owner’s manual for model-specific guidance. Verify compatibility before ordering.