Hardwick Range Parts

Hardwick Appliance Parts

Popular Hardwick Range Parts

★★★★★
★★★★★
1 Review
Fix Number
FIX11750107
Manufacturer Part Number
WPW10196405
This chrome drip bowl is an OEM approved replacement part sourced directly from the manufacturer. Drip bowls are a part for your cooktop, positioned underneath the burner to catch spills. This drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. It is common for the manufacturer to switch up designs, so it may not match your current part, however searching using the correct model number will ensure proper fit and function. Drips bowls are prone to wear and tear and can be a fire hazard if not replaced when needed. It is also a quick, easy, and cheap way to give your appliance a fresh new look. Each drip bowl is sold individually, so if you are interested in replacing your other drips bowls, they need to be ordered separately. This is also an opportune time to inspect the terminals for corrosion or damage, and the condition of the burner. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place. Give your new drip bowl a regular cleaning with warm water and soap to help it last as long as possible.
Fixes these symptoms

Installation Instructions

Henry from St Louis, MO
Replace old drip Bowls
Remove heating elements, remove old drip bowl, install new drip bowls replace heating elements. Read more...
★★★★★
★★★★★
4 Reviews
Fix Number
FIX11750108
Manufacturer Part Number
WPW10196406
This chrome drip bowl is an OEM approved replacement part designed for use with various models of electric ranges and cooktops. This drip bowl fits under 6-inch burner elements and has a diameter of approximately 8 inches. It sits under the burner, keeping any drips and spill contained. It is common for this part to become discolored, corroded, or otherwise damaged with time, and will need to be replaced. Each drip bowl is sold individually, so this is a good time to check the other drip bowls on the appliance in case you would like to replace those as well (sold separately). No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place. By routinely cleaning this part, it will help to prolong its life.
Fixes these symptoms

Installation Instructions

Henry from St Louis, MO
Replace old drip Bowls
Remove heating elements, remove old drip bowl, install new drip bowls replace heating elements. Read more...
Light Bulb - 40W
$11.72
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX884734
Manufacturer Part Number
8009
This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and unscrew by hand to replace. It is designed to tolerate extreme temperatures, which is why it is commonly used to light the inside of refrigerators and ovens. Depending on the appliance and location of the bulb, disconnecting the power is recommended. This bulb is sold individually.

Installation Instructions

Helen from Quincy, MA
lightbulb in refrigerator went out
Removed plastic shield on top of refrigerator. Removed old bulb.. Replaced new bulb. Reinstalled plastic shield. Voila! Read more...
Drip Bowl - 6 Inch
$10.09
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX2366565
Manufacturer Part Number
W10196406RW
The drip bowl is used for electric ranges or cooktops with the coiled style burners, to catch any drips, spills, or crumbs that may occur while cooking. If your bowls have become discolored, corroded, difficult to clean, or otherwise damaged it may be time to replace them. This repair is easy and does not require any tools to complete the job. Ensure that all burners are turned off and cool to the touch before starting. First you need to lift up and disconnect the burner from the socket. While you have the burner out, it is a good time to check it for any signs of damage. Look at the terminals for any signs of arcing or burning. If you notice this, you will want to replace both the element and the receptacle it plugs into. Remove the old drip bowl by pulling it out. Then insert the new one by lining up the small hole on the side with the element block. Ensure that it is siting flat and then plug the element back into the socket. Please note that the manufacturer has substituted this part, and it no longer has a solid bottom. It is not recommended to cover the hole with products like aluminum foil, as it can trap heat or melt, becoming a fire hazard. As it is an OEM part, it ensures it will fit your model. The drip bowls are sold individually, chrome in color and about 8 inches in diameter, made to fit under a 6 inch burner element.
Fixes these symptoms

Installation Instructions

chris from ABERDEEN, SD
Burner would not heat up and the cook top on light would not turn off.
First turn off breaker. Pull out stove and unplug. There was about 8 screws on the panel on the back side of the control panel. Remove panel. Remove knob on the bad control and there is 2 screws behind knob. Remove those 2 screws and take the new control and remove 1 wire at a time from old switch to new one then put back together. Read more...
Surface Burner Plug-In Block Kit
$13.41
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX340571
Manufacturer Part Number
330031
This is a genuine OEM replacement part. This surface burner plug-in block kit is designed for use with surface elements of your ranges and cooktops. This kit helps connect the wire harness to the surface element. If your element is not heating, or if it only heats intermittently you may have an issue with your terminal block. This is a newer-style terminal block kit, it includes the plastic receptacle block, two metal brackets, two pre-crimped hi-temp wire leads with terminals, two ceramic nuts, two screws, and heat shrinking insulators. Before beginning this repair make sure you have unplugged your appliance.
Fixes these symptoms

Installation Instructions

Doris from Skoke, IL
Elements heat sporatically
I followed the steps in the instructions which were very easy, once the electric power was turned off to the range. I replaced 2 burner plug in blocks in less than 30 minutes. I am embarrassed to say that these burners have not been functional for almost 3 years. I thought that I could not work with electric. Just make sure you have the tools on hand and read the instructions first. I am a mid-50's female, if I can do this so can anyone else! Read more...
Long Oven Sensor
$34.72
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX1570174
Manufacturer Part Number
12001656
This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temperature (too hot or not hot enough), not heating evenly, or an oven that will not start. To access this part, you will need access to the back of the range. Use a Phillips screwdriver to remove the screws on the access panel. Once the access panel is removed, you will notice a hole on the right side of the oven where the temperature sensor comes out of the oven. You will need to unplug the wire harness, and then open the oven door, locate it in the upper left corner, and remove the screws holding the temperature sensor in place. Pull the sensor out of the back of the oven, and replace it with your new part.
Fixes these symptoms
  • Door won’t open after self cleaning cycle
  • Element will not heat
  • Little to no heat when baking
  • See more...

Installation Instructions

Michael from Pearl River, NY
Oven did not heat up
Removed the oven door, removed existing screws. Pulled wire carefully out of opening, unclip connection. Reattached connection screwed back new sensor attached oven door finished. Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX1570190
Manufacturer Part Number
12001676
This genuine OEM kit includes the parts required to replace a surface burner receptable on your range. The kit comes with a plastic block, a metal bracket, high temperature wire nuts, and wires. The burner elements on the cooktop plug into the receptacle, and if the burner is not heating up properly, the receptacle may need to be replaced. Other signs that the receptacle is faulty is if there is corrosion on the element terminals. Before beginning this repair, please be sure to disconnect the power supply to your range. You will need a pair of wire strippers and a Phillips screwdriver for this installation.
Fixes these symptoms

Installation Instructions

Steven from Westerly, RI
Burner Receptacle replacement
unplugged stove, removed old burner, lift top (mine did not have retaining screws), cut old wires, unscrewed Receptacle, screwed in new Burner Receptacle, used the wire strippers to strip back the old wire, then used the wire tie to connect (very very easy). done! plugged back in the new burner element (old one was burnt up) and plugged the stove back in, complete! works great! My wife loves me again! :) Read more...
Fix Number
FIX1573892
Manufacturer Part Number
12400035
This flat style oven igniter kit is a genuine OEM replacement part for your gas range. When the igniter glows white hot, the heat opens the gas valve and ignites the fuel heating the burner assembly. If your igniter is only glowing orange or red, or not glowing at all, it will need to be replaced. This kit includes the igniter, ceramic wire nuts, an insulation pad, a metal bracket, and a variety of plug ends. This kit can be used for both short or long igniters, and the bake or broil element. However, it is not compatible with ranges that require round style igniters. The igniter has an amperage between 3.3 and 3.6. The element is very fragile and should be handled with care. Before beginning your repair be sure to disconnect both the power and gas supply to your range.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Gas smell
  • See more...

Installation Instructions

David from ENCINITAS, CA
Wall oven would take a very long time to ignite.
One of the 2 screws that holds the igniter to the burner assembly was stripped and difficult to get out. Other than that it was an easy fix. Read more...
Terminal Block
$34.05
In Stock
Fix Number
FIX11750972
Manufacturer Part Number
WPW10245259
It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Touchpad does not respond
  • See more...
Oven Bake Element
$67.17
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX11744014
Manufacturer Part Number
WP74003019
This oven bake element with push-on terminals has a terminal depth of three inches, making a total element length of nineteen inches.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven is too hot
  • See more...

Installation Instructions

Patricia from West Babylon, NY
Heating element in electric stove oven broke in 2 pieces.
Ordered part which was delivered in 3 days. Called son to come and install. 7 days later son came to repair. I had watched video on how to install so I supervised(kibbitzed). He shut power off at fuse box, removed element with a screw driver, used pliers to release connection and then reversed procedure, installing the element. It took about 9 minutes. Were I younger than 82 and could bend and reach, I could have done it myself. Back to baking. Read more...

Hardwick Range Appliance Types

Related Hardwick Range Parts

Popular Hardwick Range Models