OEM Broan Range Hood Parts & Accessories

Blower Wheel

$39.08

Fix Number: FIX10432533
Manufacturer Part Number: SNT5901A000

This is a blower wheel, which also includes the clip needed to install it. This authentic OEM blower wheel is the components that spins inside the fan housing, to produce airflow. It is made of a durable plastic and is pressed onto the shaft of the mower. The bottom (closed side) of the wheel has an outer diameter of approximately 5-3/4 inches. The top (open side) of the wheel has an approximate outside diameter of 6-3/16-inches. It is about 2-inches tall and is compatible with a 1/4-inch shaft. When viewing it from the open side, it rotates in a clockwise direction.

Lens

$48.85

Fix Number: FIX10281910
Manufacturer Part Number: SB03293051

This lens is sold individually and sourced right from the original manufacturer. This clear plastic part measures approximately 3.5-inches long by 2.5-inches wide. It helps to protect the light bulb and disperse and soften the light. If this plastic part cracks it will need to be replaced. To install your new lens, no tools are needed, just remove the old lens and pop the new one into place into the brackets.

Light Lens

$39.08

★★★★★

1 Review

Fix Number: FIX10281344
Manufacturer Part Number: S99110437

This is an OEM light lens for a range hood and it is sold as an individual part. It is also sometimes referred to as a bulb cover, as this small plastic piece encases the bulb, protects and hides it. This part is easily installed by just snapping it into place, no tools required.

Installation Instructions

John C from BELLA VISTA, AR

The hood light stopped working (switch failure - not the light bulb or socket), the fan switch worked fine, but replaced anyway.

1. Shut off applicable circuit breaker to isolate power to exhaust hood.
2. Unscrewed the single machine screw holding the wiring channel cover in place. Used 1/8" nutdriver.
3. Tape labeled (R & L) the associated electrical wires to light switch and colored wires to fan switch for exact replacement.
4. Pulled off the connector wires by the metal clips using needle nose pliers (some were very stubborn (grease corrosion or tight).
5. Could not pinch the plastic expanders on switches and push through from rear as I expected. Had to pry switches from front with screwdriver, wiggle one side free, and then force switch through from back side. This was the hardest task as they fight to stay in place. They come out the front side only.
6. Inserted from the front both fan and light switches, noting the switch label positions of the new and old to get the wiring and on-off positions to be the same as the old.
7. Reconnected all the labeled wires to the new switch pole connectors.
8. Turned on circuit breaker and tested new switches.
9 . Replaced the wiring channel cover and screwed in the metal holding screw with nutdriver. Read more...

Light Lens Qt20000-A

$39.08

★★★★★

1 Review

Fix Number: FIX10282138
Manufacturer Part Number: SNTK7504000

Grease Filter

$39.08

Fix Number: FIX10281130
Manufacturer Part Number: S99010370

This is an OEM aluminum grease filter for a range hood. It measures approximately 5-7/8-inches by 16-15/16-inches. It is recommended to change this filter every six months to ensure it fulfills its purpose of removing dirt, grease, debris and odors. It can be cleaned in the dishwasher, making it very convenient to keep well-maintained. For this quick and easy repair, remove the four screws that hold the cover in place. Remove the metal cover, take off the metal wires, and remove the grease filter. Secure the new grease filter in place and reassemble.

Lamp Diffuser

$50.06

★★★★★

1 Review

Fix Number: FIX10432313
Manufacturer Part Number: S97018564

Knob, Black

$39.08

Fix Number: FIX10279974
Manufacturer Part Number: S600348

This part includes one black OEM control knob for range hoods. The control knob allows you to turn the blower fan motor and light switch on and off. This knob is made out of a durable plastic and can be easily removed by simply pulling it straight off its post by hand, no tools required. It is most commonly replaced because it no longer secures properly to the post or is has cracked or chipped.