Roper Dishwasher Parts

Roper Appliance Parts

Popular Roper Dishwasher Parts

★★★★★
★★★★★
1 Review
Fix Number
FIX11750255
Manufacturer Part Number
WPW10204131
This is a genuine OEM replacement rack adjuster for your dishwasher. If this part is damaged, broken, or missing it may cause issues using the top rack properly. To replace this part, first remove the top rack from your dishwasher, by removing the rack stop clips from the ends of the rails. To release the tabs, you can either use your fingers or a flat blade screwdriver to depress the locking tabs. Once the top rack has been removed and placed on a suitable work surface, the defective rack adjuster can be removed, once again using either your fingers or screwdriver to disengage the tabs. The new rack adjuster can then be snapped into place.

Installation Instructions

Anthony from EASTHAMPTON, MA
Both left and right front rack adjusters fell apart
I briefly watched a YouTube video and looked at the placement of the remaining two rack adjusters. They broken one were easy to take out. New ones were easy to put in. Just remove the top rack completely from the rails. I bought four and replaced all four just to be on the safe side Read more...
Seal
$66.25
In Stock
Fix Number
FIX11731683
Manufacturer Part Number
W10864081
This seal is attached to the inner cabinet to reduce noise.
Fixes these symptoms
★★★★★
★★★★★
3 Reviews
Fix Number
FIX11745488
Manufacturer Part Number
WP8268961
The friction sleeve, sometimes called a friction pad, is made of a flexible black plastic and measures a bit over one inch in length. It is designed to reduce the friction between the hinge and the door on your dishwasher, and helps keep it quiet when the door opens and closes. If the door to your dishwasher drops quickly when unlatched, you may need a new friction sleeve. The sleeve is sold individually however there is one located on both the left and right side of the dishwasher. We recommend replacing them at the same time so that they wear evenly. Replacing this genuine OEM part is an easy repair, but it will require you to pull the dishwasher out from under the counter.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Noisy
  • See more...

Installation Instructions

kathleen from Kenner, LA
after unlatching dishwasher door fell open-- no resistence
Pull out dishwasher, removed old sleeves (was split), released spring mechanism, slipped on new sleeves, re attached spring mechanism, reset dishwasher. Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX11755809
Manufacturer Part Number
WPW10509257
This dishwasher door gasket is a genuine replacement component designed to create a watertight seal between the tub and the door. Wrapping around the sides and top of the door, the gray rubber gasket prevents leaks during operation and helps maintain optimal performance. Its flexible construction ensures a snug fit, and raised edges help contain moisture within the unit. Installation is straightforward, and once installed, it is recommended to keep the door closed for several hours to allow the gasket to properly seat and form a secure seal. Compatible with select dishwasher models, this part should be verified for fit before purchase.
Fixes these symptoms

Installation Instructions

Francis from Strykersville, NY
Dishwasher leaking at bottom of door
It was real easy to change the door seal after I watch the repair video.Only after i installed the new seal it leaked worse than before.After reading up on the problem iI decided to check the float it had crud in it and the Vent in the door was full of crud and build up. After cleaning them and freeing them up. The dishwasher works great. the seam and water have to have some where to go when the machine is running., if the float is plugged the washer will over fill. and if the vent in the upper door is plugged the water will be pushed out the bottom of the door and because the door had a new seal it made more water come through the bottom of the door because it had a tighter seal. hope this helps some one. this saved me from buying a new machine. Read more...
★★★★★
★★★★★
2 Reviews
Fix Number
FIX8260087
Manufacturer Part Number
W10518394
This is a manufacturer-approved heating element and 2 washers. If the dishes in your dishwasher are not drying or the water in the dishwasher is not getting hot, it may be due to a failed heating element. The heating element is not intended to heat the water that enters the appliance but is designed to maintain the heat of the water that enters. This part is located on the bottom of the appliance. Be sure to disconnect the power to the appliance before you begin this repair. Start this repair by disconnecting the wires from the bottom of the element in the back, remove the plastic nuts holding it in place, remove the element, and repeat these steps in reverse order to install the new part. For this beginner repair, you will need a screwdriver, wrench set, and it should be completed in less than 30 minutes.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not draining
  • See more...

Installation Instructions

Jesse from Mandan, ND
not drying or cleaning dishes
Turned off breaker at power source. Turned off water supply valve. Disconnected water supply hose and drain hose. Removed base panel with 1/4'' nut driver. Removed power box cover screw with 1/4'' nut driver, turned off wire nuts connecting power cable and used phillips screw driver to remove ground. Removed 2 phillips screw under front of counter holding dishwasher in place. rolled dishwasher out of cabinet and layed face down on towels. Pulled two wires connected to the element marking position prior. Then removed two heater element nuts with adjustable wrench. Tipped dishwasher up, opened door and lifted out lower rack, underlower rack is heating element and lifted out. Reverse procedure to install. Read more...
★★★★★
★★★★★
2 Reviews
Fix Number
FIX11746591
Manufacturer Part Number
WP8565925
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that should not take very long to complete. Start by opening the dishwasher door, depress the tabs to remove both the front stop clips and remove the upper dish rack from the appliance. Now, using your small flat head screwdriver, release the retaining tab to remove the rear stop track that you are replacing, and pull the clip up to remove it. Install the new clip by inserting it into the support rail from the top and press it down to secure it in place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Richard from Austin, TX
Wheels on original upper rack adjust fell off and end stops would not stay on.
Removed old end stops. Pulled rack out of machine. Carefully removed old adjusters. Snapped in new adjusters. Slid rack back into the runners. Clipped in the new end stops. Done. Read more...
★★★★★
★★★★★
2 Reviews
Fix Number
FIX11745451
Manufacturer Part Number
WP8268655
If the top rack of your dishwasher is no long sliding in and out smoothly, you may need to replace one of the wheels. This genuine OEM parts assembly includes the wheel, the mount, the axel, and the clip. They are sold individually, and most dishwasher top racks have four wheel-mounts in total. If you need to replace more than one wheel, be sure to add the correct quantity to your cart. Replacing these are an easy repair and does not require any tools, simply pop off the broken wheel mount and snap the new one into place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Noisy
  • See more...

Installation Instructions

James from KNOXVILLE, TN
DOOR LEAKING - UPPER RACK LOOSE
EASY Read more...
Fix Number
FIX11743423
Manufacturer Part Number
WP661566
This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.
Fixes these symptoms
  • Not cleaning dishes properly
  • Not drying dishes properly
  • Will Not Start
  • See more...

Installation Instructions

Tim from Salida, CO
Dishwasher would shut down when it got to hot wash or dry cycle
turned off the water and power to the machine; removed the screws from under the counter top, turned the front feet of the dishwasher to allow the dishwasher to be pulled out. Disconnected the power and water from the machine' mopped up the water with the towel. leaned the machine on it's front; located the thermostat; unplugged the thermostat; unscrewed the screw that holds the bracket; replaced the thermostat. reversed all the above. Read more...
Fix Number
FIX11753379
Manufacturer Part Number
WPW10348269
If there is still water left in your dishwasher after it has finished running, there may be an issue with your drain pump. The pump is designed to remove water from the tub, and if that is not happening then it could be due to damaged that is causing the motor not to run or a crack causing a leak. If a new pump is required, this is a genuine OEM replacement part. Completing this repair will be easiest if you pull the dishwasher out from under the cabinet. You will need to disconnect both the water and electrical supply to the appliance before starting.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...

Installation Instructions

WILLIAM from MCKEES ROCKS, PA
Dishwasher not draining
This was one of the easiest jobs I ever did first I rremoved the excess water with a Shop-Vac then removed the kick plate two screws then removed the clamp from the drain hose pulled the electrical wiring off the pump removed the pump by turning it counterclockwise put the new pump in turning it clockwise it took less than a half-hour but a little more than 15 minutes Read more...
Chopper Assembly
$33.94
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX1734917
Manufacturer Part Number
W10083957
If your dishwasher is not cleaning your dishes properly, is not draining, or is noisy while operating, there may be an issue with your chopper assembly. The chopper is used to mince up food particles in the dishwasher, which prevents them from clogging up the pump. If you need to replace the chopper, this is a genuine OEM assembly for your dishwasher. Before beginning this repair, be sure to disconnect the power to your dishwasher. You will need to remove both the upper and lower racks from the dishwasher in order to easily access the chopper assembly. You will need a number 15 and number 20 torque screwdriver and a pair of needle nose pliers to complete this repair.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...

Installation Instructions

scott from ALBANY, OR
not get dishes clean anymore
Took apart cleaned out filters, put in new parts, work great now, clean dishes. Thanks for the repair video really helped. Read more...

Roper Dishwasher Appliance Types

Related Roper Dishwasher Parts

Popular Roper Dishwasher Models