7MMVWC200DW2 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tracy from CONWAY, AR
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My washer was always off balance.
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cranford, NJ
- Parts Used:
- W10913953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would go from sense to done without running cycles. Sometimes the drum would make a quarter turn.
I followed the video published on this site
Was this instruction helpful to you?
Thank you for voting!
Agitator wouldn't twirl.
Removed old agitator and determined teeth in center were worn down. Purchased new upper agitator assembly and repair kit. It now works like a new washer. (NOTE: It wasn't until after I did the repair that I heard 15 years is quite old for a washer. But it cost me $40 to repair compared to $500 to replace. I hope it lasts another 15 years!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Cleveland, OH
- Parts Used:
- WPW10074580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Found seal had split on agitator cap
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.
Thanks for making finding part so easy . . . .
Thanks for making finding part so easy . . . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from CLINTON, WA
- Parts Used:
- 285811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
The upper agitator would not engage (would spin freely in both directions)
I simply watched the brief video supplied on both the page as well as my emailed receipt and performed the steps as directed. There were no deviations required... it was exactly how the video described it. Honestly, I expected a more lengthy and complicated repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Freedom Ford / Rick from MCALESTER, OK
- Parts Used:
- 285811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not move
Replaced agitator sprage kit. Simple instructions simple repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from TULSA, OK
- Parts Used:
- 8575076A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Broke softner dispenser
Cleaned inners of the dispenser and snapped on new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from OGALLALA, NE
- Parts Used:
- 8575076A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The dispenser that I purchased 1 year ago broke (flaw in plastic part, I think)
My washer is an Amana He, but the part is made by Whirlpool, I think. I just set the new part on the middle agitator in the washer and pushed it firmly down and it snapped into place. It was amazingly EASY!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SAN JOSE, CA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Washer would not adgitate
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha K from Colorado Springs, CO
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
top of agitator wouldn't move to pull clothes down
Removed softener dispenser, removed part under that to reveal bolt that holds agitator on to washer. Figured out there was more to the problem than just the dog ear things and had to end up getting a whole new agitator. Probably saved us $60 minimum in labor and trip charge and was a piece of cake! Took my husband less than 15 mins. to remove old agitator and put on new one. Geez, I guess I have to do laundry again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wheel Man Enterprises, from UTICA, OH
- Parts Used:
- 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Agitator top wasn't rotating
Repair was extremely simple by using the video provided online. Works perfectly! Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from WINTER PARK, FL
- Parts Used:
- 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator did not work
The repair was exactly like the instruction vidio
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tuan from LADSON, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
On Spin cycle washer jumping all over the place.
Just follow the video! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from CLAYTON, NC
- Parts Used:
- W10913953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not step through the cycle steps, would not complete the washer cycle.
Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.
Problem is resolved, saved almost $250 by doing it myself!
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.
Problem is resolved, saved almost $250 by doing it myself!
Was this instruction helpful to you?
Thank you for voting!