7MMVWC200DW2 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tricia from HARLEYSVILLE, PA
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer walking during spin cycle
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Heath, OH
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
agitator worn
First removed the cap, took out the screw, pulled out old agitator and replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorena from Tampa, FL
- Parts Used:
- 285565
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
the agitator was making loud noises and then the top part stop working
My husband just took the bolt in the middle took the broken one, put the new one, put the bolt back the lid the rubber seal and done. Working like new.
Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.
Basically we did what everyone else did with this part, it help me realize I did not need to call a repairman for this, I knew hubby would be able to do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from S BURLINGTON, VT
- Parts Used:
- WPW10074580, W10772621, 8575076A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator broken. Bolt missing.
Had to clean out area where bolt was to go as it was full of debris. Placed agitator on, bolted on , placed softener dispenser on. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from Rohnert park, CA
- Parts Used:
- 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
upper agitator inoperable
Took ten minutes to pop upper assembly off and replace dogs. Note long ratchet or nut diver advisable 5/8.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from SNOHOMISH, WA
- Parts Used:
- WPW10074580, 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Worn out agitator directional clogs.
I just ordered the complete agitator kit since I didn't know for sure what I all needed, and it made my repair so easy replacing since it was all complete. I followed video which was a great help. Got it all done in 25 minutes. Very easy. Thank you...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from MT STERLING, KY
- Parts Used:
- 8575076A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
fabric softener wasn't dispensing
The old part popped right off, and new one installed. Works Great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MENTOR, OH
- Parts Used:
- 285565
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Had to replace the agitator
I already had the old agitator out, so when I got the new one I put it in the tub. You have to spin it a little so it seats properly. I then tightened the bolt with a 7/16” socket and my wife was washing a load within 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MAHWAH, NJ
- Parts Used:
- WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Jupiter, FL
- Parts Used:
- 285565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Partial Agitation - CAM Agitator teeth worn
1. Removed the fabric softener dispenser
2. Removed Barrier Seal Cover
3. Removed bolt and seal
4. Removed and replaced CAM Agitator Assembly
5. Reversed the removal steps.
2. Removed Barrier Seal Cover
3. Removed bolt and seal
4. Removed and replaced CAM Agitator Assembly
5. Reversed the removal steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isaac from Bridgeport, CT
- Parts Used:
- 285751
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer machine wouldn't turn
It was a really simple thing to do. Make sure to buy the agitator cam kit (a little piece broke when I was taking it apart). Take off the cover and then the nut that is underneath. Replace the agitator cam and that's it!!! Usually those agitators dog ears wear down with time so if the agitator assembly is not turning, check this first.
Was this instruction helpful to you?
Thank you for voting!
The Washer wasn't agitating.
Removed the attaching bolt and then removed the Upper Agitator Assembly. I removed the damaged parts and installed the Agitator Repair Kit and Re-installed the NEW Upper Agitator Assembly.
All of our wash was smelling like mildew. It was making us nauseas . After the repair everything smelled fresh and clean again. We received our parts within three days.
Thanks
All of our wash was smelling like mildew. It was making us nauseas . After the repair everything smelled fresh and clean again. We received our parts within three days.
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- L from Indianapolis, IN
- Parts Used:
- 8575076A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased w/o fabric softenmer dispenser
take off top on middle section (pops off) pop dispenser on--done
Was this instruction helpful to you?
Thank you for voting!