MAT14CSAWW0 Maytag Washer - Instructions

I pulled out the washer, laid it on it's back, pulled off the two hoses using pliers for the clamps, pulled back two clips, pulled off the pump from the shaft, put the new pump on the shaft, and did the reverse of the above. It was a simple operation and made even more satisfying by the prompt delivery of the part, within 2 days. Thank you for that, and I will use your services in the future if needed.

After unplugging power and disconnecting water drain hose, I pulled the washer out aprox four feet from the wall and leaned it back against the wall. I then used a lamp at the end of an ext cord to light up below the washer where the water pump was attached and it was easy to remove and replace! I carefully replaced the washer in its original location and reconnected power and drain hose. The job was complete in 15 minutes! Wow!

tilted the unit on it's back. removed clamps and hoses from pump. used screwdriver and pried off 2 hold-down clamps. removed old pump. placed new pump onto shaft. installed hold -down straps. re-installed 2 hoses. stood washer upright, releveled and turned on.

Simple. Removed two hose clamps, pulled off the hoses, removed the clips that held the pump in place and removed the old pump and then simply did the same thing in reverse to put the new pump in. It was easy and the pump was an exact match.

Had a coworker hold washer tillted back, pop both clips that hold pump in place,with pliers remove clamps from hoses.
install hoses on new pump and install pump on motor with the clips.
It took about 12 minutes to do the whole thing.
It was very easy and fast.

First, I laid the washer upon its back and removed the two clamps that held the water pump in place.
with wire pliers.
Next I removed the two inlet water hoses from the pump and sat that pump aside. I then placed the new water pump upon the shaft of the washer and secured the two water inlet hoses back on the new pump wth the clamps. I tightened them with the wire pliers slipping the clamp upon the hoses. Lastly , I snapped the two wire clamps that hold the pump in place back in their groves and immediately placed the washer up right .

Luckily this washer was in the garage and was being made ready to replace an old broken washer. Being able to lay the washer on its side made the job much easier than if it was upright in the laundry closet.

Removal of the old pump was simply a matter of releasing the two clamps holding the input and output hoses and removing the two spring clips holding the pump in place on the motor shaft.

The new pump install required a reversal of the above and took about 3 minutes. It was a very easy and successful repair.

Kayla tilted the washer backwards so I could get access to the pump from below. all I had to remove was two clips then slid the old pump off the shaft and the new one on-clip it in place.Then clamp the hoses on the new ports and we were done in about ten minutes.This made me feel good in three ways... Did A job with my daughter! Save a lot of cash!! and walk away with a great sense of accomplishment !!! Rob@kayla

My friend unplugged washer turned off water to it, tilted machine back took off old, put on new. It took him about 5 minutes. Washer is working fine now, no more water leaks!

got under machine and replaced pump

Replace front legs. Very easy fix.

Flip washer on its back, Undo/flip the clips/clamps off the water pump, remove the clamps from the hose and remove hoses from water pump, slide the pump off the direct drive, line up the shaft/drive with the new water pump and slide into position and return the clamps to secure water pump in place and reattach water hoses and clamp to the water pump. There should be two hoses going to the water pump, flip washer back upright and run a cycle to make sure the problem has been fixed

Unfortunately my washer cabinet did not come off as in the video so I had to do repair from underneath. The rest of the repair worked exactly like the video showed. I had a couple of small, sturdy wood boxes about 9" high which I used to brace the washer after tipping it backwards a bit (and unplugging it too). My wife acted as a spotter to be extra safe. The only two things that required the hook tool and mirror were: 1) Working from the bottom my hands were at an awkward angle so I couldn't pop the retainer clips off the pump, but a hook tool (like a screwdriver with a hooked end) popped them off easily, and 2) The other issue was once the new pump was in place I could not locate the slot for the top retainer clip until I could look at it with the telescoping handle mirror, and then I was able to put the clip in by feel. Extremely easy repair, especially with the guidance from the video. Thanks for video help! WH

undone 2 hoses and popped off brackets

The repair went fine and the U - Tube video was very helpful. However, the putty knife under the front corners to release a spring clip was not accurate to release the console. Our Roper had two philips head screws on each corner of the back of the console that had to be removed to allow the console to slide back and off its clips. Then the housing of the machine (sides and front) was not coming off as described. However, after measuring I determined that the water pump had enough clearance to be removed without the housing of the machine being removed. So, the repair was even simpler than described.