25331640103 Kenmore Refrigerator - Instructions

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!

Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

It simply snapped into place. No tools required. A very simple repair.

The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.

I slid off old caps, then slid on new caps. I pushed down metal holding clamps and I was finished. The whole process was about 5 minutes. The parts select web site was great. I looked up my parts on the easy to use catalog and ordered them. Make sure you save the broken parts or write down the part numbers to make finding your exact parts easier. I wish all parts web sites were as easy to use as parts select.

Ordered the right parts thanks to your list of part numbers and where they were located on the refrigerator. They fit perfect and problem fixed in five minutes. This is the best site I have ever used!

Please keep up the good service you provide.

I had to cut the retainer bar to length and then snap the end caps onto the bar. Then just snap the assembly onto the freezer. No problem!

The switch prevented the door from closing about 5 years ago. So I just taped the switch down, and lived without a fridge light for the last 5 years. Painful! And wasteful (food spoiled because we couldn't see it.) Thought I was out of luck, assuming light switches were all the same, got fed up again, and pulled out old switch,,and searched the net for the part number, and just started calling the manufacturer. I got this website after no luck in calling, and took the step to order...and in no time, got it replaced, and we cam see now! It feels like we got a new fridge!

replaced it

Popped off the old and slipped on the new. No tools - in less than 5 minutes.

I looked at the model number and ordered it through the part select. The delivery was real fast and convenient. Overal we had a very good experience with "Part Select"

Just snaps into notches on each side. Bar arrived bent from shipping. Replacement was overnighted at no extra charge. Great service.

Need to repair refrigerator for new renters. Ordered parts and received them two days later. Installed retainer bar with end caps into refrigerator door same day parts received.