TFX22PRSBWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry from Hurst, TX
- Parts Used:
- WR57X10051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
My wife called me at work and said the refrigerator was "peeing" on the floor.
When I got home I pulled the refrigerator away from the floor, checked all the water lines for leak evidence, and then took the back panel off to check everything behind. The water valve was leaking at the hose insert locations. I turned off the water, spent less than 5 minutes disassembling the valve from the rerfrigerator, and got online to buy another one. The part arrived several days before expected, and it took me less time to install the new part than it did to take the old one out. Now all I have to do is repair the floor damage I caused when pulling out the refirgerator!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Yuma, AZ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door was squeaky and would no close
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and applied a little lubricant to the cam and job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Star City, AR
- Parts Used:
- WR55X129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the icemaker kept opening and closing
First I remove the 4 screw that connect the control board to the icemaker and then removed two more screws hold the control board in place and unpluged the control board and put the new one in and plugged it back up and put all the screws back and it was done I had no more problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Brunswick, OH
- Parts Used:
- WR12X869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Discolored Door Handles
Easy to do - first use a butter knife to remove the decorative cover on the handle trim - then unscrew clean and replace - done in 15 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ravi from Rochester, NY
- Parts Used:
- WR55X129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The switch for the ice and water dispenser broke.
First I shut off the water supply and disconnected the power to the refrigerator. Remove the two finger tabs that are used to for the light swirch and ice/water by pulling straight down. Remove the cover to the dispenser assembly by pulling it out by hand. I removed the four small phillips head screw in each corner of the assembly. Pull the assembly out just enough to expose the circuit board connectors. Note the color of the wires and their position and location. The connectors are different sizes and should not be confused. Remove the two connector by pull them out straight. You can remove the entie assembly , but pay attention to the the water actuator when the assembly is removed entirely to prevent damage. Place the the dispenser assemby on a solid surface and remove the two screws holding the circuit board in place. Pay attention to the position of the black circuit board retainer be fore removing it. The circuitboard should be removed by pryiing gently on each side until it is released. Reverse the procedure for installation of the circuit board..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Gardnerville, NV
- Parts Used:
- WR55X129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Water / ice cheap plastic selector knob broke off.
First I shut off the water to the refrigerator and unpluged the electrical cord. Then I unsnapped the cover to the control board assembly located above the ice/water selector knob. Then removed four screws holding the control board assembly. Then I tilted the assembly out far enough to unplug the two sets of wires connected to the control board. Then I removed the two screws holding the control board to the plastic assembly. You are then able to lift the control board out of the assembly. Be careful tilting out the assembly. I pulled too hard and removed the whole thing from the refrigerator which disconnected the ice/water actuator lever and I had some problems getting it re-installed correctly. Installation is basically the reverse of removal. I suggest testing it before snapping back on the final cover plate. I wouldn't recommend trying this repair unless you've done some kind of basic automotive or appliance repair... you can always try it and call a repairman if you get stuck. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from alameda, CA
- Parts Used:
- WR12X869
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
old handles-----dirty,stickey
removed upper and lower facia strips, exposing the screws holding on the handles. replacinf the metal strips was trickey---they bend easily, and are difficult to get them to snap back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from norwalk, CT
- Parts Used:
- WR1X5278, WR17X11349, WR57X57, WR02X11330
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water lines to ice maker and door dispenser replacement
replacing the lines was easy, problem was the drawing on line and the parts list did not show two different size tubing used. had to run out for the 5/16 inche tubing for the water dispenser in the door. got the 1/4 inch tube done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Houston, TX
- Parts Used:
- WR55X129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
In-Door Ice Dispenser Not Working
The solenoid that opens the ice chute would fire, but the ice auger would not turn in either direction. I verified that the motor was OK by running 120 V to it directly. Changing out the "timer board" was a 15 minute job and did the trick. Ice galore!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dianne from loxahatchee, FL
- Parts Used:
- WR55X129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water indoor was not working
I received the part after doing what was instructed by process of elimination for the problem.I installed it and it still didn't work. I took the part out and called to return it but was told i couldn't because it was now a used part and your company only sells knew parts. Now, I have a circuit board that I have no use for.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Harrisonburg, VA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
icemaker stripper fall a part
instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.
Dremel and it works!The instalation part of the "job" was less then 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from New Albany, MS
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker didn't work.
Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Callaway, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Ice maker arm disconnected from frame causing problems.
The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BROOKLYN, WI
- Parts Used:
- WR12X869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door handles worn out, cracked, looked terrible
After contemplating for months on replacing my GE side-by-side refrigerator and realizing the only reason I wanted to is because the door handles were disgusting, I found this site and decided to try to replace them first. After reading other instructions shared, it was a relatively simple fix. You'll need a flathead screwdriver to pop off the trim and a torque screwdriver to remove and reinstall the handle screws. That's it. Looks great! Wish I would have done this sooner as it would have saved me a lot of worry time. The cost of replacing my refrigerator is a nice perk, too!
Was this instruction helpful to you?
Thank you for voting!