GCE23LHYDFSS General Electric Refrigerator - Instructions

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

look at how the unit was put together and disassemled it pice by piece and labeled parts as i took them of in order then reversed when i reassembled

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

1. Removed the back panel of the fridge to get access to the inlet water valve.
2. Removed black poly water line from valve (pull back on white ring where line is attached and pull the line out)
3. Removed the inlet tube from top-back of fridge (where it goes into the ice make). use putty knife to get under the sticky white gasket beneath the black oval housing and pull the tube out form the back of the fridge.
4. Replace the water line with new part taking care to properly seat the line into the the bottom water valve and pushing the water tube into the hole for the ice maker.

Note: Be sure to take off the protective covering from the white - sticky grommet and push to adhere to metal on fridge.

to be safe - use a bit of clear silicone chaulking round the perimeter of the grommet and push to tighly bond the water inlet tube to the fridge.

The reason for this - is that if you do not get a good bond using the white - sticky gormmet alone - you may have the water tube inside the ice maker freeze up.

Also once the new water line is installed be sure to secure the line to the metal back of the fridge - so the line will not move. some fridges come with metal hose clamps to do this - otherwise use duct tape

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

Replacing the water filter with the new style water filter was no problem...twist to the left, drop the old filter, line up arrows on housing and new filter, twist to the right and done.

Ice maker was always crusing ice. There is a spring deflector wound around the actuating rod towards the back of the ice dispenser. Pulled the ice dispenser out, slid the damaged spring off, and slid the new spring deflector on making sure to engage the actuator rod to restore it's action. Easy fix.

replaced with new connector and it worked great. also replaced the water filter and that was super easy!

I took the part out of the package and placed it in the recessed water dispenser/ice maker cavity. Done!

Emptied the door bin, removed it from its slots, and gently spread the plastic bin sides allowing the broken face panel to fall out. Replaced one end in the notches, gently widened the opening at the other end to slide the new face panel in, and jiggled just a little to seat the panel fully. Done!

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

To take the ice dispenser apart is not difficult. A ring removal tool would have helped to remove the auger. The Auger nut was difficult to remove and I used a visegrip to pull it off. Once the retaining ring was removed the repair was easy.
Never did it before but figured it out.

several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!

Removed tension spring, removed old lever, installed spring on lever, inserted lever in hole, re-attached spring to hook under front of refrigerator.

Water line 5/16inch was severed, under refrigerator. Used union connector to join line. Dispenser plate removed using allen key to unsnap plate ,from under the plate itself. Removed screws holding solenoid valve and removed the plug from circuit board connected to solenoid. Installed new solenoid valve. Put flapper back in place, and made sure spring on left side of flapper is reattached to the opening on the flapper. This corrected all problems. Caution, keep an eye on spring that it remains in place.