ZCE23SGTDSS General Electric Refrigerator - Instructions

Replacing the water filter with the new style water filter was no problem...twist to the left, drop the old filter, line up arrows on housing and new filter, twist to the right and done.

Ice maker was always crusing ice. There is a spring deflector wound around the actuating rod towards the back of the ice dispenser. Pulled the ice dispenser out, slid the damaged spring off, and slid the new spring deflector on making sure to engage the actuator rod to restore it's action. Easy fix.

replaced with new connector and it worked great. also replaced the water filter and that was super easy!

I took the part out of the package and placed it in the recessed water dispenser/ice maker cavity. Done!

I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor
Peter

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

1. Removed the back panel of the fridge to get access to the inlet water valve.
2. Removed black poly water line from valve (pull back on white ring where line is attached and pull the line out)
3. Removed the inlet tube from top-back of fridge (where it goes into the ice make). use putty knife to get under the sticky white gasket beneath the black oval housing and pull the tube out form the back of the fridge.
4. Replace the water line with new part taking care to properly seat the line into the the bottom water valve and pushing the water tube into the hole for the ice maker.

Note: Be sure to take off the protective covering from the white - sticky grommet and push to adhere to metal on fridge.

to be safe - use a bit of clear silicone chaulking round the perimeter of the grommet and push to tighly bond the water inlet tube to the fridge.

The reason for this - is that if you do not get a good bond using the white - sticky gormmet alone - you may have the water tube inside the ice maker freeze up.

Also once the new water line is installed be sure to secure the line to the metal back of the fridge - so the line will not move. some fridges come with metal hose clamps to do this - otherwise use duct tape

To take the ice dispenser apart is not difficult. A ring removal tool would have helped to remove the auger. The Auger nut was difficult to remove and I used a visegrip to pull it off. Once the retaining ring was removed the repair was easy.
Never did it before but figured it out.

Really easy to install - they both snapped into place.

Removed tension spring, removed old lever, installed spring on lever, inserted lever in hole, re-attached spring to hook under front of refrigerator.

Emptyed shelf of food. Aligned new plastic front piece. Pressed front. Went right into place.

unscrewed lamp and replaced it with new one!

All I had to do was slide it in. But that's not what made me so thrilled with your site. What won my devotion was your site's ease of use (I couldn't find what I was looking for on GE's site) and the promptness of delivery. I will certainly use you again and recommend your services to my friends!

1. I unplugged the refrigerator/ freezer
2. Turned off water supply
3. Removed the screws that held the cardboard skirt in place
4. Unplugged the water tube from the push connect
5. Removed the screws around the water inlet to the ice maker
6. Remove the water fill tube
7. Install new water fill tube and put all the screws and plates back where they go

I am a 64 year old woman.I will 65 in March. I do the plumbing and painting at our house and my husband who is 67 does the carpenter work, I help him by holding boards he is sawing etc. I though the job would be easier than it was, but it was still easy. I took out the first screw which was in plain sight, secound screw I could not get to, and thought oh no I will have to take some other things apart. but when I removed the screw to the ice maker shield it was easy to slide it down out of way, and I got to 2nd screw pretty easy, I removed 2nd screw put new slide in place put screws in place started 1 st screw, then 2nd screw then went back and tightened 1st and 2nd screw, put the ic maker shield back in place tightened the screw slide ice bucket back in place, and though now this will be ready for company coming for the Holidays.... YEAH....