PSF23MGWC General Electric Refrigerator - Instructions

Repair man said we needed a new circuite board, which I ordered and installed, however didn't fix the problem. Freezer was still freezing up, so I ordered a new defrost heater and thermostate. Installed yesterday, so it will be a week or so before I can check to see if this repair is working. However, replacement of these parts was very easy, and online ordering and delivery service the best. Keeping fingers crossed this repair does the trick. Best, Mike

I removed the old shelf and installed the new one!

1) Unplug Refrigerator. Remove all shelves and light shield in the freezer.
2)Remove panel covering refrigeration coils inside freezer in back. Two hex head screws w/nut driver.
3)Remove the defrost heater using phillips screw driver. Two screws.
4)Unplug two quick disconnect stakons and wires from heater.
5)Plug the wire coming down the right side into one side of the new heater and plug the shipped white wire into the other quick disconnect spade at the heater.
6)Install the new dual element defrost heater into the same place where the old was. Connections to the right.
7)Route the wire that was on the left across the top of the coils and down the right side.
8)Bring the existing wire from the left side down the right side and the white wire up the right side. Wires should not be tight at all and do not remove the tape at the stakon.
9)Now wires need to be cut (if necessary)and crimped together in the shipped stakon. This stakon looks like a wire nut.
10)Wires should be tucked gently into the styrofoam up and down the right side. Wirenut should be positioned so that water can not collect in it.
11)Replace the panel over the cooling coils.
12)Plug Refigerator back into the wall outlet. Put shelves and light shield back in.
13)My refrigerator is now working without a problem. It's been est two weeks.
Ice maker is also working correctly.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

I searched YouTube for the problem and was quickly taken to several videos that detailed to required actions. This encouraged me to proceed, so I took the back cover off and found the water valve leaking. I then googled the make and model of the frig and found the part. The YouTube videos provided all of the details needed to determine the problem and replace the faulty part. Once the part arrived, I was able to install the new one in a few minutes. Operation returned to the water dispenser and the leak was gone. Total cost of the repair was $56 and took about 1.5 hours to remove the original part, order the replacement and install it when it came. Perfect!

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

Replaced defrost thermostat along with temp sensor watched the video on this page simple fix

I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor
Peter

I removed the ice from the tray, took out the four screws from the tray, pulled up the metal spiral took out the old drive cup, replaced with the new one, replaced the screws and put the tray back in the freezer. A piece of cake. Thanks for your prompt service and the reviews on how to replace.

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

Both parts were easy to install and they fixed the problem. It is a two person project as it is very hard to get both hands inside the freezer section because it is so narrow. Be sure to orient the wire nuts in the right direction to avoid condensation and follow the instructions to create a drip loop on the wire connectors. We reviewed many "fix it" forums and almost bought the mother board. Really glad we found parts select, saved over $100.

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

I removed the 4 screws from the cradel then I wedged the tabs open on the unit and removed the main operating mechanism .Ithen removed the broken parts and reassembled the mechanism I put the unit back together in
reverse order. It works just fine.