GLVC25V7FB2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator door was not closing properly, Bits of black plastic had been breaking off from lower hinge area.
My husband researched the possible causes on line and watched some of the videos that were posted on your site. I ordered the 2 parts which did come in 3 business days. My husband and son completed the repair in under 30 minutes. Unscrew the upper hinge assembly on the top right door, lift the door up so that the lower hinge pin is free. Remove the old worn closer plate and hinge bearing. Replace the door, replace upper hinge hardware and check alignment. (It was also a good time to do a thorough cleaning on the coils underneath the refrigerator and check the evaporator pan.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WAVERLY, MN
- Parts Used:
- 5303918455
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
bottom hinge on door was broken made a clicking noise everytime you opened the door
just followed the instructions
Was this instruction helpful to you?
Thank you for voting!
The refrigerator door had a loud clunking or popping sound when opened or closed
Followed the instructions using a internet tutorial. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from TUCSON, AZ
- Parts Used:
- 5304520331, 240457701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dood didn't close properly
followed instructions on your video.. PERFECT and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cloid from HOOVER, AL
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice Director Door Broken In Half
I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from INVER GROVE, MN
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Every part of the ice crusher (blades and housing) bent/broke in successive failures
This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from SAN CLEMENTE, CA
- Parts Used:
- 240350903
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problem
As it turns out when i pulled the drawer out and then the door holder i discovered that there was a big piece of material that was suppose to be around the water line that was causing the problem. The old drawer holder was not the problem so the new piece was not needed. All is well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from MYRTLE BEACH, SC
- Parts Used:
- 240351061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Crisper drawer was cracked and needed to be replaced.
I ordered the replacement part, and when it arrived, I used a flat-blade screwdriver to remove the two glides from the old drawer and installed them on the new drawer by snapping them into place. Then I removed the sliding humidity control from the old drawer using gentle pressure, and installed it on the new drawer. Then I slipped the drawer into its place, loaded the vegetables into it, and was done in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Westville, OK
- Parts Used:
- 241685101
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The center of the plastic auger drum was broken
Had to replace with a whole new part, had to take it all apart to replace
Was this instruction helpful to you?
Thank you for voting!
Worn out bearing
Unscrewed tye top door bracket lifted off the door and popped on new bearing takes minutes to do. Takes more time to empty thenshelves beforentaking door off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arden from Hainesville, IL
- Parts Used:
- 240328203
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The refrigerator door made a loud clicking noise when it opened and closed.
We took the door off the hinge which invovled removing the top screws on the door. The part that broke split in two pieces leaving the shank inside the bottom of the door hinge. The most challenging part of the repair was pulling that piece back out since there was very little to grab on to. Once we got that out it was easy to replace with the new piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Marion, KY
- Parts Used:
- 240328203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The refrigerator door popped when opened past 90 degrees.
This was an easy repair. I had already read about the same problem from another of your customers and followed his directions. But more remarkable than the ease of the repair was how quickly I received the part. I ordered the part, using standard delivery, at approximately 2:00 on Thursday afternoon and received it the next morning and had the refrigerator repaired within 24 hours of ordering the part. That's service.. Thanks
Was this instruction helpful to you?
Thank you for voting!
when refrig door open it made a "clicking" noise.
The noise was made due to a loose part. I took the refrigerator door off and replaced the closer plate and hinge bearing. This solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Mount Juliet, TN
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass shelf
slipped the shelf on to the bracket........done!
Was this instruction helpful to you?
Thank you for voting!
Shelves Were Broken
Ordered the shelves from partselect. Com and just replaced the new shelves in the space where the old shelves were.
Was this instruction helpful to you?
Thank you for voting!