GLVC25V7FB2 Frigidaire Refrigerator - Instructions

repaced ice/water filtration (by pass ) hopeing it would fix problem . was not sucessful !

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Took the part out of the box and slid it in to place. It fit perfectly!

Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 screws and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!

This site sent me an installation video along with my shipping confirmation details, by email. It was very simple to do after viewing the video.

inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!

I REMOVE THE TOP COVER AND PLATE KEEP DOOR CLOSE TO HOLD IN PLACE THEN LIFT THE DOOR OFF REMOVE THE SCREW IN CLOSER PLATE REPLACE NEW ONE POP OUT BEARING IN DOOR WITH SCREW DRIVE REPLACE THE NEW ONE REINSTALLED DOOR EASY REPAIR.

just followed the instructions

Followed the instructions using a internet tutorial. No problem.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

followed instructions on your video.. PERFECT and easy.

My husband researched the possible causes on line and watched some of the videos that were posted on your site. I ordered the 2 parts which did come in 3 business days. My husband and son completed the repair in under 30 minutes. Unscrew the upper hinge assembly on the top right door, lift the door up so that the lower hinge pin is free. Remove the old worn closer plate and hinge bearing. Replace the door, replace upper hinge hardware and check alignment. (It was also a good time to do a thorough cleaning on the coils underneath the refrigerator and check the evaporator pan.)

Remove the food items from the shelves on the door, Phillips screwdriver to take the top cap off. Adjustable wrench to take the two screws off the top hinge. Lift out the door and set aside. Remove two bolts from the lower hinge, reinstall with the new hinge and spacer. Reinstall door on lower hinge. Lift into place to reattach the upper hinge. Put the food back in and you're done.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

I watched the instructional video and did what it said.