MGT8775XS00 Maytag Range - Instructions

This is a double oven unit. Both the upper and lower igniters are easy to get to, with just a few screws to remove. However in order to reach the quick disconnects, the back of the oven needs to be removed. So there are a bunch of screws to take off and the oven needs to be moved away from the wall. Pulling out the igniter wires and putting the new ones back in, is easy. Then put all the screws back on and move the oven back to the wall. Don't forget to disconnect the power when you do all this.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

The steel mounting screw tends to seize in the aluminum burner head. It is not easy to extract, or to drill out and rethread. My advice is to replace the burner head at the same time.

I determined the bake igniter was not working. If the bake ignitor does not work, the sensing unit to turn on the gas does not activate. I examined the bake igniter it was blacked significantly in one spot. There were no apperant cracks in it. I did a web search for the part and ordered it. Three days later it was delivered. Take pictures of each step if you fell the need. Pull stove away from wall turn off the gas, unplug power cord, remove panel in back of stove that covers the electrical, unplug the ignitor/element. Move to the front of the range and remove the oven rack. Remove the cover over burner tubes, it secured with several screws. Remove wing nuts for heat shield. Carefully remove burner tubes along with the attached ignitor/element. You will have to carefully guide the ignitor wires out with the burner tubes. Unscrew ignitor from the burner tube, attach new ignitor/element. Reverse the steps.

ordered new broiler pan

unscrewed screws in the back of the stove. inside the stove, replaced the old bake igniter with the new one and connected the electrical wire in the back of the stove.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Just replaced insert pan - was able to identify it on the internet web site by inserting model number. Ordered part on line and got it within a week! Easy peasy!

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Removed two screws on sensor in the oven. Pulled out stove and after unplugging same removed the back panel. Sensor has an electric connection on the rear of the oven with a connection that is easily separated. Threaded new sensor electrical connection through inside of oven and connected on the back of stove. Pushed insulation back around the wire were in goes through to the oven. Replaced back on stove and screwed in two screws which hold sensor inside the oven. Replaced back cover on stove, plugged it in and pushed it back in place. Did the trick for me..

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

A fairly simple fix that this website did a nice job helping me diagnose and select the part. Only tricky part was the electrical connector on the range side had been cut so I had to splice the wires which wasn't a big problem. Just take your time to find the nuts and replace one part with another.

Followed instructions I found online at the Maytag site.

very simple fix. I removed the bake burner cover (the blue cover on the bottom of the oven), under that is the oven baffle which is held on with one wing nut and removed that. Then remove the oven bake igniter screws(two on the side), remove the orifice cover scew and remove then remove the oven bake burner gently. once these parts are off you need to remove the screws on the back of the oven ( I believe theres about 4 or 5 along each side and there are 4 on the bottom of the large metal plate. you only need to remove the large metal cover every thing else stays put. Disconnect the lower back burner attatchment which just clips into the connecter. once thats removed the part should come out easlily from the inside of the oven. Now take the new bake ignitor and feed the wires through the opening on the inside of the oven that allows the wires to come through to the back of the oven(you may need to feel around for the wires and move some of the insulation aside to feel them) once the wires come through the back connect the new part by clipping it to the harness the old part was removed from. At this point you should be able to reassemble the back of the oven exactly the way it was removed.Now go back to the inside of the oven, replace the bake burner gently over the bake burner orifice and put the orifice cover back on and reattach with it's screw. Position the bake igniter back into place on the side of the bake burner and replace the two screws previously removed. Once thats in place its time to put the oven baffle back on and secure with the wing nut and the last step is to place the bake burner cover. Just set the oven to bake and it should be working if thats in fact the problem..Good luck. Took me less than 15 minutes to fix.Some find it easier to remove the oven door but I didn't need to do this since I had enough room to access the front and the back of the oven without any trouble.

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??