Jump to:
Product Description
This oven igniter helps start the bake burner by heating up and lighting the gas. It’s compatible with several major brands and can fix issues like no heat, uneven cooking, or a burner that won’t light. Before installing, turn off the power and gas supply, and handle the part with care.
-
Works with the following brands:Maytag, Whirlpool, KitchenAid, Jenn-Air
-
Works with the following products:Range
-
Fixes the following symptoms:Little to no heat when baking, Will Not Start, Element will not heat, Gas igniter glows
-
Part# W11596211 replaces these:74007965, 7432P143-60, W11532055, WP7432P143-60
- Works with the following brands:
- Maytag, Whirlpool, KitchenAid, Jenn-Air
- Works with the following products
- Range
- Fixes the following symptoms
- Little to no heat when baking, Will Not Start, Element will not heat, Gas igniter glows
- Part# W11596211 replaces these:
- 74007965, 7432P143-60, W11532055, WP7432P143-60
Part Number Cross Reference
Questions and Answers
Be the first to ask our experts a question about this part!
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts Additional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
- Customer:
- David T from Salem, OR
- Parts Used:
- W11596211
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom oven would not heat up.
ordered the bake igniter and installed it now the oven works fine. all done from the inside of the oven no problem whatsoever.
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from LANSDALE, PA
- Parts Used:
- W11596211
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Lower oven would not heat up.
Step 1: Unscrew wingnut on the bottom plates and remove the two plates.
Step 2: Unscrew back left protective plate over the gas inlet. Next remove the screw holding down the gas tube. (Note the orientation of the bake igniter wire for reassembly) Gently slid the tube to the right to disconnect.
Step 3: Remove the tw ... Read more o screws holding the bake igniter.
Note: I screw all the screws back in there holes so I do not mix them up or loss them.
Step 4: Remove the back cover of the oven. Start by removing the two screws just above the gas value. Next the two screws on the bottom left. Next remove the side screws. Don't forget to disconnet the emergence shut-off line from the gas value. Now remove back cover.
Step 5: Disconnet the bake igniter connector. (Have a buddy lightly pull the old bake igniter in the oven a little bit to find the correct wire in the back). Tie a string to the old bake igniter and pull through into the oven. Retie the string into the new bake igniter and pull bake through to the bake. Reconnect to the wire you originally removed it from.
Step 6: Starting backwards from Step 4, reconnect the emergency disconnect lin E into the gas valve. Reinstall the back cover.
Step 7: Reinsert the gas tube back into the gas inlet. Make sure you guide the bake igniter wire around the back of the gas tube as noted in step 2. Screw tube back in place. Reinstall protective plate over gas inlet. Now, very carefully (igniter is very fragile), reinstall the two screws to fasten the bake igniter onto the gas tube.
Step 8: Reinstall the two cover plates from Step 1 and install the wingnut.
Fingers crossed, try starting the oven. It should fire up. Good luck with your repair.
Step 2: Unscrew back left protective plate over the gas inlet. Next remove the screw holding down the gas tube. (Note the orientation of the bake igniter wire for reassembly) Gently slid the tube to the right to disconnect.
Step 3: Remove the tw ... Read more o screws holding the bake igniter.
Note: I screw all the screws back in there holes so I do not mix them up or loss them.
Step 4: Remove the back cover of the oven. Start by removing the two screws just above the gas value. Next the two screws on the bottom left. Next remove the side screws. Don't forget to disconnet the emergence shut-off line from the gas value. Now remove back cover.
Step 5: Disconnet the bake igniter connector. (Have a buddy lightly pull the old bake igniter in the oven a little bit to find the correct wire in the back). Tie a string to the old bake igniter and pull through into the oven. Retie the string into the new bake igniter and pull bake through to the bake. Reconnect to the wire you originally removed it from.
Step 6: Starting backwards from Step 4, reconnect the emergency disconnect lin E into the gas valve. Reinstall the back cover.
Step 7: Reinsert the gas tube back into the gas inlet. Make sure you guide the bake igniter wire around the back of the gas tube as noted in step 2. Screw tube back in place. Reinstall protective plate over gas inlet. Now, very carefully (igniter is very fragile), reinstall the two screws to fasten the bake igniter onto the gas tube.
Step 8: Reinstall the two cover plates from Step 1 and install the wingnut.
Fingers crossed, try starting the oven. It should fire up. Good luck with your repair.
Read less
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from Rice Lake, WI
- Parts Used:
- W11596211
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not start
I took out the bottom of the stove, then the burner along with the igniter. Took off the back and unplugged the old one and plugged in the new one and put everything back in place, It was very simple to do.
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Oakhurst, NJ
- Parts Used:
- W11596211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Top oven would not ignite.
Removed cover over burner via wing nut, removed burner assembly via 2 screws, loosened igniter via 2 screws, loosened rear cover via 6 screw/nuts and disconnected igniter electrical connection and then pulled out old igniter. Replaced new igniter via reverse method. Was very easy repair for a reasonable guess diagnosis. Just happy it w
... Read more
asn't a "controls" problem.
Read less
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
★
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Eleuza S - June 3, 2019
Verified Purchase
Perfect fit
Perfect fit
Model Compatibility
This part works with the following models:
Fix Number: FIX16744717
Manufacturer Part Number: W11596211
Manufacturer Part Number: W11596211
| Brand | Model Number | Description |
|---|---|---|
| Kenmore | 66578002800 | Range |
| Kenmore | 66578002801 | Range |
| Kenmore | 66578002802 | Range |
| Kenmore | 66578002803 | Range |
| Kenmore | 66578003800 | Range |
| Kenmore | 66578003801 | Range |
| Kenmore | 66578003802 | Range |
| Kenmore | 66578003803 | Range |
| Kenmore | 66578003804 | Range |
| Kenmore | 66578009800 | Range |
| Kenmore | 66578009801 | Range |
| Kenmore | 66578009802 | Range |
| Kenmore | 66578009803 | Range |
| Kenmore | 66578009804 | Range |
| Whirlpool | GGG388LXB00 | Range - Freestanding, Gas |
| Whirlpool | GGG388LXB01 | Range - Freestanding 30" Gas |
| Whirlpool | GGG388LXB02 | Range - Freestanding 30" Gas |
| Whirlpool | GGG388LXB03 | Range |
| Whirlpool | GGG388LXB04 | Range |
| Whirlpool | GGG388LXB05 | Range |
| Whirlpool | GGG388LXQ00 | Range - Freestanding, Gas |
| Whirlpool | GGG388LXQ01 | Range - Freestanding 30" Gas |
| Whirlpool | GGG388LXQ02 | Range - Freestanding 30" Gas |
| Whirlpool | GGG388LXQ03 | Range |
| Whirlpool | GGG388LXQ04 | Range |
| Whirlpool | GGG388LXQ05 | Range |
| Whirlpool | GGG388LXS00 | Range - Freestanding, Gas |
| Whirlpool | GGG388LXS01 | Range - Freestanding 30" Gas |
| Whirlpool | GGG388LXS02 | Range - Freestanding 30" Gas |
| Whirlpool | GGG388LXS03 | Range |
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.