22314 (1988) Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from ARCADIA, FL
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
worn out burner switch
easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Temple, TX
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned burner control out of warranty
switch power supply off at breaker panel
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken Surface Burner control
Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from GAITHERSBURG, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
burner control stopped functioning.
Replaced the control.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from San Antonio, TX
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our old element cartridge had broken.
To repair, I just pulled out the one unit and replaced with the new. Took longer to get the unit out of the box. We are greatly pleased. Ordered on Thursday and had the unit by Saturday. Saved over $100.00, WILL shop PartSelect again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sandra from Breckenridge, CO
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Jenn Air stove top grill had stopped functioning
I decided to remove the original Jenn Air grill from my stove top and replace it with a new Jenn Air radiant Element Cartridge. I searched on Google for 'Jenn Air radiant top' and immediately found just the item on the PartSelect.com website. I placed the internet order that day and two days later -- kaboom - the part has arrived. I pluggedd it into the stove top (no tools needed) and it was better than new. Wow, that's what I call a great experience! Thanks PartSelect. - Sandi Phillips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from PICKERINGTON, OH
- Parts Used:
- A122BA
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Radiant cooktop unit died, needed to replace
Unpacked the new cooktop, plugged the module into the outlet. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Chehalis, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
burned up switch
Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Colorado Springs, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Truxton, MO
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new coil cartridge
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Control switch would not operate
Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nora from Inez, KY
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old elements were getting old.
I took them out of the box, Took the old Elements out and put the new ones in, It was a piece of Cake, You have wonderful girl working for you, she was just great. thanks for the good service. my range looks like a new now. Nora
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cincinnati, OH
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
elements were worn and not heating properly
Repair was very easy for anyone to do,Just lift the old element cartridge up and pull out,And insert new the one! Very simple it took less than two minutes.The New element cartridge(stainless steel) Fits perfectly and functions perfectly.Ordered parts on a Saturday and they arrived Monday! impressive!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Burns, TN
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burned out element
Opened packaged slid new element into place and turned on. End of that job. Cooked dinner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Salem, OR
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
elements did not work
Take cartridge out of box, slide into slot, done.
Was this instruction helpful to you?
Thank you for voting!