22307 (1988) Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Monmouth, OR
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken oven door hinge
I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Covington, TN
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had only 2 burners on Jenn-Air stove
Remarkably easy. We had purchased a Jenn-Air with 2 burners and a grill. We found we rarely used the grill feature. We needed more burners. We looked several years ago but it was quite expensive to replace so we suffered through it. I decided I had to find the replacement part or purchase a new stove. I found your website and was shocked to see you carried what I needed. The new part was half as much as we previously priced it for. So, we ordered it and it worked immediately. Thank you so much. Saved me from buying a new stove. Linda
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vito from palm desert, CA
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced grill for 2 more burners
Took out of box and plugged into slot.....even I was capable of doing this....easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Centralia, WA
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old element did not work
just plugged it into the unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Norwalk, CT
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cartridge was old and worn out.
Pulled out the old one, pluged in the new one. It took me longer to open the box! PartSelect made it so easy to order and the shipping was super fast and at low cost. I looked on ebay and saw people paying more (with shipping and handling) for used parts. Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from New London, WI
- Parts Used:
- A341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grill cover was getting old and discolored
We ordered the part for replacement. You sent it and we just put in on the stove. It was exactly what we wanted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Sedro-Woolley, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Lefrt Front Burner Quit Working
Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from EAST LYME, CT
- Parts Used:
- A405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Install New Vent Cover
Installation was straight forward as the new vent cap was sized correctly for exhaust pipe (5 inch). Placed the mounting plate into the exhaust pipe and used 4 SS screws to anchor to house sheathing. The vent flapper was not flat, requiring that I carefully stress relieve it at 250 degrees and hold it flat while cooling to take warp out. Snapped it in place afterwards and then bolted on cover.
Was this instruction helpful to you?
Thank you for voting!
both burner switches failed intrenally
simply remove and replace th switches using a screw driver an a pair of needle nose pliers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ARCADIA, FL
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
worn out burner switch
easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr. Mike F from SAN ANTONIO, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door hinge
My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Savoy, IL
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no heating element
I think Part Select is great, but my story? I just plugged in a module.
It was so easy...well...a technical writer--one of those people who writes operation manuals--could have done it. But afterward, they wouldn't have been able to explain to anyone other than another tech writer how it was done.
It was so easy...well...a technical writer--one of those people who writes operation manuals--could have done it. But afterward, they wouldn't have been able to explain to anyone other than another tech writer how it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Dunnellon, FL
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The 6in burner would go to max heat regardless of the setting.
Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above
fine.Of course I did shut off the power before starting any of the above
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HOT SPRINGS, AR
- Parts Used:
- WP74008014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken oven door hinge
My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.
John - Hot Springs Village, AR
John - Hot Springs Village, AR
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HELGA from INDIAN TRAIL, NC
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
jenn-air coil element was old (1983) just needed to be replasted
took the old one out ,poped the new one in, took 2 minutes
Was this instruction helpful to you?
Thank you for voting!