22307 (1988) Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old coil went out
I pulled out the old cartridge cleaned the stoptop up. Plugged in the the new cartridge ..there was a little steam left over fromt he cleaning when I turned up the heat but it went away. Looks great and save me $3k the difference in the price of a new stove top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Baton Rouge, LA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old filter to replace
:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from Gloucester, MA
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cartridge did not heat
Unplugged the old element and plugged in the new one.
The best part was it arrived less then 24 hours after I ordered it. Unbelievable, thank you.
The best part was it arrived less then 24 hours after I ordered it. Unbelievable, thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lebanon, TN
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element was bad and couldn't locate anywhere else for this price. Outstanding service and phone assistance. Will use again for sure!
Simple repair. Unplugged element cart. and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- connie from demarest, NJ
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cooktop did not heat up
Just unplug the old broken cartridge and plug in the new one. It was very easy. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Williamsburg, VA
- Parts Used:
- 674744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
One of the two door springs broke
I followed the instructions that came with the spring and found them to be very complete. The repair was easy. The repair involved removal of the lower access door, installation of the new spring and replacing the access door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from Las Vegas, NV
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fan switch broken
No problem, except the holes in the clips to hold the switch in were so small that the clips would not go over the pegs.
The solution - use supper glue.
The solution - use supper glue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from Milton, MA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element was cracked
I took out the old heating element and pluged in the new one. Very simple. Just like putting a plug into an electrical outlet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josee from San Antonio, TX
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan was not working.
Took less than 15 mins to remove the old switch and replace for the new one.
Works like new!
Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from Henderson, TX
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners quit working
My old burners pluged in. I pulled out the old burners unpacked the the new burners pluged them in. I turned on the new burners and tested themand they worked!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Port Republic, VA
- Parts Used:
- 12001129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
installed new fan switch for counter stove top
The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from St Louis, MO
- Parts Used:
- 12001129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Fan switch was shot
Easily removed the switch housing. After that, the other experiences really helped me as the retainer rings on the old switch would not come off and I broke one of the threaded posts about a eight of an inch from the base. I pried the other one off, more carefully, with a screw driver and a vice grip pliers . I was already to use the "super glue" solution when I luckily found an old nut that fit the one remaining threaded post.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hackensack, MN
- Parts Used:
- YA145A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
needed a new burner for the range
Took out the old burner & replaced it with the new burner. Wanted a raised burner for large pan & kettles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yong from Houston, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Eureka, MO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Any setting selected (1 thru 9) would result in the surface burner going to full hot
Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.
Was this instruction helpful to you?
Thank you for voting!