SVE87600B Jenn-Air Range - Instructions

I contacted a local appliance repair store who didn't know what I was talking about. I looked online and the store called me back to tell me the part would probably be $75.00. I took the broken part out of the door frame and found the exact part online at your site, and ordered it for $14.00. Received the part within 2 days and put it in in 10 minutes.

I took the broiler pan out of the shipping container and put it in the oven.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

I cut off the electricity. Removed the back panel. Moved 1 wire at a time from old board to new board. Then removed the old board and replaced the new one. Reattached the back panel and turned on the electricity. I was happy when the oven began to heat.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Turn off the electrical breaker before starting! Open the oven door & remove the 4 silver hex head screws under the bottom of the control panel with a 1/4 " nut driver. Pull out on the bottom of panel. This will access the clock assembly. Unplug the ribbon cable by pushing in & up on the small clips on each end of the connector - this is a little tricky but not that difficult. Remove the two small connectors and remove the two clock assembly mounting screws. Reverse the procedure for installation. This corrected the problem with the broil element not working - apparently the electronic clock assembly was the problem there as well.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Removed screws on face plate, disconnected wires, placed on counter, removed hex head screws. Removed one end of electric type circutry, replaced with new part and reassembled.

I first turned the power off to the stove at the junction box. Removed the control panel that contained the clock assembly by removing 4 phillips head screws. While my wife held the control panel, I disconnected the two pin connectors and one ribbon connector attached to the clock. I then removed the two phillips screws holding the clock assembly in place. To disconnect the ribbon connector, press the release buttons on the side in and the center loosens and pulls out, releasing the ribbon. There are two plastic tabs that fit into two guide holes on the ribbon. The best part of this is that 6 months ago, two number keys and the timer button had quit functioning and I thought I was going to have to replace the touch panel also. Apparently it was a problem with the circuit board on the clock assembly because everything works now! My ife is very happy!

Turn off power to the stove. Pop off the burner knobs and remove the screws attaching the controls to the front panel. Open the oven door and remove the four screws attaching the panel to the oven frame. The panel slides down giving easy access to the circuit board. Remove the two connectors and the ribbon cable attached to the board. There are small clips on the side of the ribbon cable connector that release the ribbon cable. Unscrew the board and install new board. Reattach the cables, put the panel back in place and attach. Reattach the burner controls to the panel, pop the knobs back on, power the stove back on, put on a pair of sunglasses to view the now blazingly bright display and admire your work.

Turned power off to oven, removed control knobs, took out four screws under panel. Removed four 1/4" sheetmetal screws. Removed front cover, Removed two additioanl screws that held front cover to corner bracketts, Removed two screws that held clock to plate, removed each wiring harness and pluged into new part, unplugged wiring ribbon from old part plugged into new. reassembled. Turned power back on and tested and we had light!!!One repair company was going to charge us over $400 to make this repair!!!

Open oven door
Remove two sets of four screws underneath the LED display
Remove stove handles (pull off easily - no tools needed)
Lower flat plate width of oven and about two inches deep should be able to drop out from under the clock display.
Remove face plate over clock.
Unscrew four screws holding clock unit down.
Undo two electric connectors and the thin ribbon connector - the thin ribbon connector is different - the ribbon comes loose and the black plastic connector stays in place on the board.
Press the thin ribbon connector ends inward and pull up to detan ribbon on old one and then to insert ribbon on new one.
Reverse the rest.
Not too bad!

Loosened the contol panel until I was able to get to the Digital Display board.
Removed the three cables and the screws that held the display unit to the control panel.
Reversed the procedure to instll new digital clock display unit.

My microwave is stacked on this stove. I had to pull cover off to slide part off. screws were a snap. only problem was the slip catches on the ribon strips. Sperating with flat head was scary but worked fine.