SVE87600B Jenn-Air Range - Instructions

I removed the screws that held the element in place. I then pulled the element out and disconnect the two wires. Connected the wires and place element in place and screws to hold in place.

Note: this is the second part that I acquired to fix the problem. Had I listened to my wife the first time the problem would have been solved the first time around because she made the correct diagnosis.

very easy, removed two screws, unplug the wires on the old element, replug the new element , replace the screws.

Unfotunely this was not the entire problem. Ended up purchasing a new stove.

Just replaced old with new, it plugs in same as old.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

I removed the 4 screws that hold the control assembly to the range and observed that the clock assembly/control board appeared easy to remove.

Ordered the replacement board and it came a day sooner than the shipping I paid for. Only took about 10 minutes to take the control assembly off again and install the new.

There were no instructions with the part....the ribbon connection to the board was a little tricky to figure out...when I first released the clamps that held the ribbon to the board and pulled the ribbon out, I thought I damaged it....never seen a connection like this.

The range works fine now but it should be noted that this part is the logic control board for the entire range. The board malfunctioned over a period of time. First time, the entire oven shut down in the about half way through the preparation of Thanksgiving meal a few years ago. I couldn't bring it back to life and luckily, we had another oven to finish the turkey.

Next, we had trouble with the electronic pilots on the burners. You would turn the knob for one burner and it would attempt to light another burner.

Then the oven would not shut off when the Cancel/Off button was pressed. Would have to go and trip the main breaker to turn off the oven!

This replacement part cost $126 which is a bargain considering a new oven would cost over $2000. And it works great now. But I don't trust this appliance and I get this feeling that I threw good money after bad.

However, my experience with PartSelect was great and I will use them again. I just hope I don't have to spend more money on this applicance.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

I only had to unscrew two screws to remove the existing element. Unfortunately, when I removed the element I found that the electrical wire connected to it had melted off, so the element is actually still good. I had to strip the wire back and put a new wire connector on. Once that was done I hooked the element back on and screwed it back together.

We simply removed the front knobs, the 8 screws underneath the front panel and dropped down the control panel. We removed two screws holding the assembly and removed the ribbon cable and the two other connectors. We put the new one in and reattached all the cables and reassembled and it worked great. Took 15 - 20 minutes.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

Very simple. A few screws removed, disconnected a few wires, reattached the wires, put back the screws all without a single cuss word

lift out old filter, wash, put in new filter.

I took the broiler pan out of the shipping container and put it in the oven.

it took me longer to get my portable screwdriver from my shop than to remove four screws from the panel and two screws from the clock assembly and to unplug and replug wiring , then reassemble the panel

There were only 4 screws to remove to take off the thingy that houses the electronics portion. Then, there was a ribbon connector and two push on connectors to unconnect. Unscrewed the 4 nuts holding the faulty Assembly in place, replaced with new Assembly, and reversed the process.

That easy. The only problem was making sure which of the parts we actually needed.