SVE87600B Jenn-Air Range - Instructions

piece of cake KILL POWER AT BREAKER BOX. Remove burner knobs exposing 4 screws. Open oven door exposing 4 philips srews, four 1/4 hex head screws, and 2 philps screws for end caps. Had to pull out range about an inch (less) away from countertop. Remove screws. Move end caps away from face plate.Pull out face plate. Pull down / out bottom plate to expose Assembly. Unclip wire connection, carefully pull out ribbon connection. Remove 2 screws. Install in reverse.

Turned off the breaker. Removed the screws under the front panel and eight screws behind the burner controls (two each). I then slid out the panel and laid it flat on top of the stove. Removed the three connectors. Most difficult was the ribbon connector: Squeeze the clips at each end and slide the top half of the connector up. Then the ribbon slides out (practice on the new part). Only two screws held the assembly in. Reverse the process with the new assembly. Worked great!

This is the second clock I have had to put in this unit in about that many years. The first time I disassembled far to many things. This time I knew to only unscrew the front panel and side triangle plates. The process was much faster the second time. I hope this is not a chronic problem though.

This slide out range requires that you remove two screws that hold the element into the back of the oven, slide the range out, remove a metal cover, and then disconnect the two spade connectors from the element. Reverse is the opposite. I could not find the element anywhere locally. I live in a rural area of the Smokey Mountains. Thanks to PartSelect, I was up and running in only four days.

EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.

As described by many others before. Turned off the power at the circuit breaker panel for the house. Unscrewed the front panel, disconnected the three connections to the old assembly and unscrewed the assembly.

Cleaned a few pieces then screwed in an connected the new assembly, put it all back together, turned on the power, said a prayer and IT WORKED!

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

I first turned off the circuit breaker for the range. I then I removed the four hex screws from the underside of the panel and then dropped the panel to expose the clock assembly. I then removed the two screws holding it in place, disconnected the cables and removed the old unit. I then reversed the procedure to install the new unit. I next turned on the circuit breaker restoring power to the range. And like magic I once again had light. I know I must have made by Daddy proud. I should have done it sooner. Thank you for making it so easy by sharing the "how to's" with me. It was especially helpful to have the model number.

Cut of electricity. Opened the oven door and removed some screw that were over the door that let a plate be removed. Then that let the part drop down that was holding the clock. I removed 2 screws that was holding the clock in place, unplugged the 3 connectors that feed the clock, attached the 2 screws back in that held the clock, put the part back up in place, added the plate and was done. Turned the power back on. I was delighted when I saw the clock light on. Easy to install.

I looked at the schematic from PartsSelect, undid the 8 screws and replaced the clock assembly. I probably saved $200 on labor doing it myself. I had the clock repaired in 30 minutes.

Once the display became too dim to read, I removed the front panel to determine how to access the piece and to check part numbers so that I could order the proper piece. Once the part arrived, being familiar with the disassembly, it was simple enough to replace the part quickly. The part came out with two screws and the connections were standard electronic multi plug, making the replacement simple. When we turned the power to the unit on, it worked first time.

always remeber the first thing to do when working on electric components turn off the breaker
remove 2 screws securing the element, pull the element out enough to view the wire terminal attached to element and remove with needle nose plirers ,apply to new element ,replace screws

1. Removed knobs and front panel. Disconnect wiring.
2. Order part and installed. Done

First I took the screws off of the top hood which can be found right underneatch, this allowed me to access the panel bolts and unscreww them. We then got it far enough so that we could easily replace the old with the new and plug things back in and we were good to go. I am not sure but we must have save hundreds of dollars in a repairman.. This website is awesome..

The front panel was removed by unscrewing six screws just above the oven door and then four nuts were removed fron the burner assy. using a nut driver. The circuit board with the clock assy was then available. It was then just a matter of removing three cable connectors and a ribbon cable connector and two screws to remove the old clock assy. The reverse was done to install the new clock assy. The whole operation took about 15 minutes.