JD968SK2SS General Electric Range - Instructions

Very easy to remove the parts and to reassemble

I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.

Use screwdriver to pull down tab on both hinges. Good hind on door and as you lower to full open door will come off. Pull old bottom, insert new bottom and put door back in slots. Close and then reopen to first position and push tabs back up to lock position

Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.

1) Shut off power to oven
2) Removed oven door using snap down hinges on door
3) Removed 4-phillips head screws holding the oven frame to cabinets
4) Pulled oven out of cabinet and set it on stool in front of opening
5) Remove 2-hex screws holding metal shield covering the electrical wiring on back of oven
6) Unplugged bad thermostat connector
7) Removed the single hex screw holding thermostat inside the oven
8) Pulled the thermostat and lead wire from oven
9) Fed the new thermostat wire into inside back of oven
10) Reverse steps 1-7

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

REMOVED 2 SCREWS AND LOWERED LIGHT ASSEMBLY. UNPLUGGED THE OLD ONE, AND REPLACED IT WITH THE ITEM SENT TO ME

First, I turned off the power. I removed the fixture that held the bulb and gently used narrow type pliers to pull the old pins out and allowed the broken glass to fall upon a shop towel in the bottom of the oven.

The replacement bulb and different type of wiring connections. I cut and formed them to fit the receptacle. I gently inserted the new bulb, placed the glass cover back on. Then, screwed the unit back into the top of the oven.

Happily, when power was turned back on the light shone brightly!

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

Turn off breaker, disconnect electrical wiring, remove cooktop from courter top, turn over , remove switch.

I thought it was the burner thermostat, so I replaced the burner unit. By coincidence, the ceramic outer portion of the burner was cracked in two places, but otherwise intact. That was not the problem, though since the new burner did the same thing as the old one. Then I new it was the Infinite Control Switch, so I ordered it. Replacing it was easy. I turned off the cooktop circuit breaker and made sure no power was going to it. It is powered by 240 volts so you need to be very careful to turn off the power before doing any servicing on it. I then carefully pried up the glass cooktop and lifted it out, so it wouldn't break. By taking off the control knobs, and removing several small Phillips head screws all around the metal cooktop frame and just under the edge of the glass cooktop, I could lift the glass top off from the cooktop, and place it on some newspaper so it didn't get broken. It is important to keep the rest of the cooktop upright. The burners are not fastened down, and only gravity holds them in place. They normally sit on two springloaded pins, one on each side, and the weight of the glasstop pushes them down to their proper setting. So don't mess with them, and make sure each side remains on the two pins after you're done and before putting the glasstop back on. As for the switch, you need to remove two small 1/4 inch metal screws (a socket is very handy for this), one on each side of a metal framework that holds all the switches. After removing that framework, I carefully turned it over and found the correct switch for the burner that wasn't working. In my case, it was the closest right hand burner, which is also the biggest and has the option of having a big, small or both elements turned on, depending on how you turn the control switch. I then carefully pulled off each wire lead, with a needlenose plier to avoid damaging them, and immediately put each wire onto the corresponding same connection on the new switch. Take a close look at the wires on the old switch to make sure you plug them into the same connectors on the new switch. It's pretty straightforward. There may have been one or two small screws holding the switch onto the framework, but I don't recall right now. It was very easy to see how to remove and then reattach it. Then reverse the above steps and reinstall the cooktop, turn on the power and you should be in business!

Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.

The thry was rusty I took the door out And i slide out the thry it's take five minutes I did it by myself now my oven Look like a new I'm so happy now I get the part quickly thank you

Replaced bottom bake heat unit

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.