JVM1490SD003 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lee from Spartanburg, SC
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass turntable broke when being washed.
Ordered the part on Monday, it was delivered on Wednesday, only paid for standard shipping. All I had to do was put it in, right part, back to new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from North Palm Beach, FL
- Parts Used:
- WB15X10069
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broken
Removed plate inside door cover and removed old screws and plastic handle. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from NAPA, CA
- Parts Used:
- WB15X10069
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken handle
Removed inner trim panel. Bottom screw was visible But upper screw was behind metal frame that trim plate snaps onto Removed that to access screw. Door latch had to be removed to. Not a big deal just be sure spring on latch is reinstalled same way it was removed. Took longer than expected but way cheaper than a service call. Part arrived on time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Springfield, VA
- Parts Used:
- WB10X10021, WB06X10216
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
install new latch and spring in door
removed key pad then removed latch assembly and replaced it with new latch assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelia from Streamwood, IL
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Esther from Brooklyn, NY
- Parts Used:
- WB06X10311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cover fell apart
removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Anchorage, AK
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Orlando, FL
- Parts Used:
- WB07X10429
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Vent Grille Tabs
First I called General Electric and was told they had the vent grille part and would ship it for $95.00. I then went on line and found the same part number at PartSelect.com. They quoted me a price of $75.00 and I purchased it on line. It arrived within 3 days and had the new vent grille on my G.E. Profile Oven/Microwave within 30 minutes of opening the box. All I did was remove the two screws from the broken grille, removed the grille and put on the new vent grille with only a screwdriver. I highly recommend Parts Select as they exceeded my expectations.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Hillburn, NY
- Parts Used:
- WB10X10021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Just recently fixed and my son broke it a week later...
My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pines, from Middletown, NY
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven D from Seminole, FL
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray: need replacement part
Took item from sealed box and removed protective bubble wrap. Placed tray in microwave, aligning tray with turntable sprockets. Perfect fit, perfect match! And the part arrived in three days and was very competitively priced. What more is there to stay? Will use PartSelect for other replacement parts. No brainer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Meridian, TX
- Parts Used:
- WB10X10021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door latch
I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out
Was this instruction helpful to you?
Thank you for voting!