106482394 Kenmore Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Dennisville, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
ice maker kept filling tray, dld not empty
replaced the element as described. it worked for 2 cycles and flooded the capture tray. I thought it may be an issue with the water supply line so I replace it and insured it was getting a good feed.
I have now shut the unit down and restating it . thank you for your concern. Any tips would be appreciated.
I have now shut the unit down and restating it . thank you for your concern. Any tips would be appreciated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Parker from Bangor, ME
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
icemaker unit leaked
followed instructions and replaced unit.
very easy and will roder again from this
very easy and will roder again from this
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Escondido, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside coating of ice cube tray had worn away
Very easy. I unplugged the electrical connection of the icemaker from the refrigerator and removed 3 screws. I plugged in the new icemaker and replaced the screws and that was it, a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Bordentown, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
leaky ice maker to no ice at all
Parts arrived amazingly fast. Replaced top ice maker and bottom water control valve[which was probably the source of my problem all along] in about an hour. The online installation video's were a big help. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandford from South Toms River, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker stopped working
I ordered the replacement ice maker on a Saturday, received it on the next Tuesday, and in stalled it in a little over 15 minutes. Very quick, very easy. Partselect.com was easy to use and exceeded my expectations on every issue. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glessner from Spring Hill, KS
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker tank leaking
I removed one screw from lower portion of unit and loosened 2 top screws. Lifted unit to slide off top screws and unplugged unit. Plugged in unit and positioned unit on 2 top screws. Installed bottom screw and tightened top 2 screws. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond D. from Farwell, MI
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heater didn't thaw ice, stripped eject gears! no ice!!!
added lowering clips to brackets, plugged it in,
hung on sidewall. Plug in power, turned water on,
had ice in an hour. The written directions could be a little more detailed..I am very satisfied with the ease of installation.
hung on sidewall. Plug in power, turned water on,
had ice in an hour. The written directions could be a little more detailed..I am very satisfied with the ease of installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from shalimar, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
replaced ice maker
three screws and a plug in and it was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph A from Sachse, TX
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Icemaker not working properly
The icemaker was an exact duplicate of the one in my refrigerator. I installed the correct shutoff bar on the icemaker and removed the tab for the water fill spout. After pulling the power cord I loosened the two top screws with a nutdriver and removed the bottom screw. I pulled the icemaker from the rear wall, away from the fill spout, and disconnected the wire harness. Installation was just the reverse of the removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oxnard, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped
Replaced ice maker very EZ, How ever needed to replace ER pannels also very EZ
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from La Porte, TX
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Motor quit on icemaker
Unplugged the frig and took out the ice tray.Removed 3 screws and slid the old unit farther out. Removed the cover and released the electrical connector. Took out old unit.
Removed cover on the new unit and connected the electrical connector ,seated new unit in and reattached the 3 screws. replaced cover and plugged in the frig. Ice started making about 45 mins later.
Removed cover on the new unit and connected the electrical connector ,seated new unit in and reattached the 3 screws. replaced cover and plugged in the frig. Ice started making about 45 mins later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimbo from Smyrna, GA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Icemaker stopped making Ice.
Took out three screws and replaced the icemaker and it started working. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Tigard, OR
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker overflowing by several ounces each time.
Three hex head screws and electrical plug and ten minutes. I'm a hero. I had wasted several hours trying to adjust the old one. Throw it out and put the new one in. Ten minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tigard, OR
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no ice
removed one screw (socket), loosened two more, lifted out unit, disconnected power cord. reverse removal proccess. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Abilene, TX
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker stopped making Ice
The repair was really easy, the part arrived that would fit different designs, and with a screw driver and appropriate plug in connector, the unit was making ice better than ever.
Was this instruction helpful to you?
Thank you for voting!