106482394 Kenmore Ice Maker - Instructions

I first removed the bottom screw then loosened the top two screws about 3 turns lifted an then slide icemaker out a couple inches then used small screwdriver to unclip the wire conector and removed icemaker then pluged new icemaker in and tightened top screws replaced bottom screw lowered metal arm and was done. les than 10 min. it has taken me longer to write this reply than it did to install the icemaker.

Unplugged the fridge. Got a light to shine on 3 small screws. Used a pair of channel locks to get the pigtail wiring harness off and the old one was out. Put the new one back in, plugged in the wiring harness and heard the ice bin getting it's first new ice a few hours later.

Searched PartSelect database for replacement. Double checked pictures on website to confirm exact replacement.

After locating the screws, removed icemaker, disconnected cable connection.

Verified new part side-by=side with replacement. Made needed mod to icemaker water inlet. Popped in replacement ice maker, connected wiring harness, tightened screws. Waited for ice to arrive about an hour later.

New inlet valve. very easy. Part select was great. I first ordered a new ice maker, this did not fix the problem. Part select allowed me to return it and get the right part. The repair vidio was great.

While it probably could have been remedied with the controller, the cost difference between the controller and the unit made me opt for the entire unit. The fridge is a side by side, which meant in order for me to see the screws I'd need to use a mirror. Once I got the socket on the nut, it wasn't difficult to back out the upper screws. The lower was a bit easier. The power cable however was frozen from years of attachment, and really defied removal. Once removed, the unit came out easily. In my case, the wires had to be removed from the old unit and reinstalled in the new. Not a big deal, but just another step. the issue I had was upon re-installation. The wire harness didn't want to reassemble, and since I could only fit one arm inside, it was difficult to get the connector attached and tightened. I was able to get a pair of channel locks across the connector and get it together. Once that was done I hung the unit back on the upper screws, verifying the fill tube was properly set. I then re-tightened the lower screw. I then turned on the water and it seemed to take a very long time before the unit actually filled with water. It's now been several hours and the ice is starting to once again collect in the bucket.

As directed in video clip, an excellent instruction video. Made for one of my quickest trouble free repairs in a long while.

After diagnosing the ice maker wasn't working, I got the model & serial number of the refrigerator. Picked the ice maker online by picture, that was a first. Three screws to take the old one out and replace the new. Written directions confirmed there is no manual cycle button on ice maker. Waited a couple hours and checked it, there was ice! Everybody was happy.

Followed instructions from online video. Used the opportunity to clean the freezer compartment really well. Also discovered that water solenoid valve was failing and have since replaced that also.

I watched the demo on how to replace the ice marker and it was that simple. I removed three screws and unplugged it from the freezer. The difficult part was removing the wire on, off switch. You must pull it out carefully. It is a sung fit.

Removed three srews holding the ice maker in place. Unplugged the wiring. Plugged in new ice maker wiring. Installed the new ice maker with the three screws. I left the old wiring in place. Works perfectly.

I took out the bottom locking screw and loosened the top two screws. I took the old icemaker out. I disconnected the wiring harness at the ice maker. I attached the new icemaker and mounted it in place. I didn't have to use any of the included wiring harnesses since the old one worked fine. I did use the old wire bale. I'm fairly ungifted in fixing things so I was amazed at how easy and inexpensive this was. The icemaker started up right away. The whole thing probably cost less that just the service call minimum would have been.

Lossen two screws at the top and remove one at the bottom and lift the unit off of the top screws, unplug the old unit and after cutting out the tray for the water fill spout plug the new one in. No problem .................

Removed three screws and unpluged wiring. Replaced new unit by plugging in wire and replacing three screws.

Removed bottem screw and loosened two top screws. Removed icemaker from support screws and disengaged cable. Replaced in reverse order. Total time was about 15 minutes.

Great DIY experience. Ordering the part was easy and delivery was very fast. Simple installation and had my first cubes in apprximately 15 minutes.

. . . thanks!

Removed the old ice maker and replaced with new.