106482394 Kenmore Ice Maker - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Granbury, TX
- Parts Used:
- 4317943
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
ice maker not dumping ice often enough to keep up with useage.
Replaced ice maker with new one but found it was not the ice maker at all. There was an accumulation of ice in the duct inhibiting the flow of cld air to the ice maker. I cleared the ic build up in the duct and it has been working just fine. But am concerned about make up water leaking into the duct.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from Missouri City, TX
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker would not make ice.
Troubleshot to the icemaker as per the troubleshooting guide that came with the refrigerator. Could not initiate a harvest cycle by jumping the appropriate test ports on the drive side of the ice maker. Verified the proper voltage was present with a DVM. Ordered new ice maker, really easy on-line with PartSelect interface. Installed new unit in about 5 minutes and the unit dropped the first batch of ice about 2 hours later. Works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Eureka, NV
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Icemaker wouldn't make ice any more.
My husband followed the schematic and went step by step. When he was done, he wasn't sure he had done it right, but in about 20-30 minutes we heard the first ice drop down and it's been working ever since. He's a great handyman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stewart from Okeana, OH
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
My In-Law's Side by Side freezer-Fridge. The ice maker had not been working for over a year. Just filling with water which leaked into the ice container.
Went easy with both the video as shown on the site and the instructions provided. Hardest part was fitting my arms into the narrow freezer to get to the mounting screws. Otherwise, perfect match on the part and didn't need to use the substitute wiring provided. Allow~ an hour for the new part to cycle to refill and start making ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Gainesville, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Icemaker stopped working
My icemaker stopped working. After a day of no ice, I ordered the replacement icemaker. It arrived two days later (fast -- I was expecting it in 3-5 days). That same day, the original icemaker popped out a few ice cubes. So I waited to see what was going to happen. Every few hours, it popped out a few more cubes. So I waited awhile longer. After two days of slow-motion icemaking, my good old icemaker went back to making tons of ice all the time. I guess it just needed a few days vacation -- just like the rest of us. I called to tell PartSelect, and they cheerfully told me how to return the part for a refund.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oxnard, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped
Replaced ice maker very EZ, How ever needed to replace ER pannels also very EZ
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Jefferson, MD
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Ice maker leaking into bin
Needless to say, the ice dispenser was useless, just one big glacier of ice. I ordered the replacement ice maker and had it within two days. The instructions were perfect and the installation went without a hitch. Actually I was a bit disappointed, I had planned on spending an hour on the repair and was done in 15 minutes. I will definately use PartSelect again in the future!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Ormond Beach, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Had quite making ice.
Removed the screws holding the ice maker disconnected the wire harness and attached to new ice maker replaced screws and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Gulfport, MS
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice make leaking
watched the video on your websie. directions were easy to follow. ice maker works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Morehead City, NC
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No Ice
My unit came Fed X opened carton looked over instructions .Got out my nut driver loosened 3 screws and unpluged.Unit came out easy,Did not have to change anything except on off rod .Re installed less than 20 minutes had ice in about 2 hours. Very satisfied customer. Thanks JR
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darren from Elkton, MD
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker inop
3 quarter inch mounting screws,1 electrical connecter,and then swap over the on/off bar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Nashville, IN
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
ice maker stopped working.
3 screws and a plug. ice maker came out. Installed in reverse order. Real easy...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Potomac, MD
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
none
followed online instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from SNEADS FERRY, NC
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Timer Motor quit
Simply unplugged the refrigerator then loosened the screws. Removed the old and put in the replacement icemaker. Easy as pie to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Broken Arrow, OK
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
After replacing my water dispenser valve the ice maker didn't immediately begin making ice, so I thought I needed a new ice maker
After an overnight from the installation of the new water dispenser valve, my ice maker began making ice again. I had thought that I had made a wrong diagnosis and needed a new ice maker, so I ordered one. By the time my new ice maker arrived, I already had a bin half full of new ice cubes,
Was this instruction helpful to you?
Thank you for voting!