EE2107 Speed Queen Dryer - Instructions

I just followed the video instructions and really they were not as good as some of the customer descriptions which were far more detailed. It was like an experienced repairman telling another experienced repairman how he has been doing this repair for 20 years. The customers get into the kind of detail that is very helpful. More important parts select never tells you to read the blogs first before ordering your parts. $100 later I bought a new GE dryer which I would have done 10 days ago had I known Maytag has a repetitive problem with the high limit thermal fuse which no one has a cure for. So I did a whole bunch of repairs replacing parts on a dryer which needed to be replaced.

First we had to virtually take the entire dryer housing apart - not very user friendly. We found that one of the two mounting screws on on of the rollers was gone. The mount was just wobbling around which caused the roller to fail and all of the noise. The wheel removal was a bit tough since there is very little room to pull it up and off of the center post. Definately need at least one helper to pull up on the drum while the wheels are removed and installed. Once the two new rollers were in place, the dryer worked like it was new. Not an easy job, but very do-albe - saved a ton of money doing it myself. Two must - haves: good set of snap ring plyers and one patient helper.

Went on line to this sites video's to diagnose the problem. Steve Ash is EXCELLENT. Put idler& roller replacement video's in my Favorite File! Ordered parts PS11741930&PS11741913 from this site on line. Good price, Fantastic 1 1/2 day delivery (Fed Ex ) Referred to great videos for installation. Hints: 1) Be sure to identify ALL wires 2) Be careful removing snap rings from rollers, I stretched mine and had to reform them.(new ones did not come with the rollers. 3) It would be a good time to replace the belt & drum pads when the drum is out.

Used a dolly to move the drier out in the garage to give myself some room to work...remove the bottom panel--2 screws at the bottom...remove the door--2 screws at the bottom of the door, disconnect the 2 switch wires and then it slips out of the top....remove 2 screws from the top and swing the top all the way back out of the way---it'll just hang there.....remove the front drum support--4 screws.....slide the drum forward while working the drive belt off of the drum.....you can now see the 2 drum support wheels.....at that time I got my shop vac and got all the lint and crud outa there......remove the snap ring on each wheel, slide off the washer and wheel, pay attention--the wheel has a front and back.....reinstall the new wheel with washer and snap ring (i put a small dab of grease on the wheel support)....I also put a dab of grease on the belt tensioner wheel support--same little snap ring retainer.....reinstall the drum by sliding it in slowly as you work the belt back into place....install the front drum support--roll the drum by hand to make sure your belt is on properly.... resecure the top, then the door, and finally the bottom....when facing the drier my left wheel was in way worse condition----this is obviously because it is located right in front of the heating element....thanx and good luck....

remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

I tested all the thermostats and fuses and the heating element with a VOM. I found that the thermal fuse was bad and replaced that and it heats fine. The hard part was reaching everything from the front of the dryer. Poor design for access. Also replaced the door switch while I had it apart.

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

Step by step, I removed the bottom front panel with a putty knife to compress the spring clamps, removed the inner lint trap, disconnected the door switch and springs and blower connection under the drum, removed the lint trap/ blower housing, remove nuts at bottom sides of door panel, lift top front of dryer (putty knife, spring clamps) to remove nuts at the top then removed the door panel. I then released the belt from the (spring) pulley and pulled the drum out. Pay attention to how the seals were put on! I removed the old seals and cleaned off the old adhesive with acetone and a steel scrubby( wear gloves when using acetone and when applying new adhesive, and work in a ventilated area!) Follow instructions for applying the adhesive for the seals. Put back together in reverse order. Repair successful!

I followed the online video on PartSelect website. No other instruction necessary.

Watched the videos first. Unplugged the dryer plug. lifted the top of the dryer and braced it. removed the front cover and bulkhead and disconnected the wires. Removed the drum and belt. removed the 2 screws to the motor plate to replace the idler pulley. installed the belt around the drum and inserted the drum. routed the belt around the idler pulley and checked for alignment and twists. reinstalled the bulkhead and the front cover. plugged the dryer cord back in and listened to a quiet dryer. The dryer also dried the clothes in one setting. Yahoo and saved a bunch of money fixing it myself. I recommend to anyone to watch the videos on site to diagnose dryer noises. You'll be amazed and save money doing it yourself.