EE2107 Speed Queen Dryer - Instructions

took frount off ,then filter, pulled drum out, then blower plate & spun impeller off. went back together easy ,except belt . that gave me a little problem but finally got it thanks

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

I should have know it was the fuse from the beginning but I figured this out after replacing the the heating coil. (I didn't have the tools to test the wiring, and everyone kept telling me it was the heating coil.)

Anywho, I replaced the thermostat first then the fuse. They were located on the outside cabinet of the heating coil. I plugged it up and then there was heat. They did look a little different from the original ones but you could tell which was which. The fuse is at the top and the thermostat at the bottom. I didint have to use the new wiring to the fuse because they looked fine. I did however had to use the wiring that came with the kit for the thermostat because the old one was fried and a little different from the original.

Well that's my story. Sorry if there's any lackness in the details.

Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.

Well first of all you get to the back of the dryer from the FRONT.. after lower panel was removed location of the heating element was right in front of you. Two 7/16 sheet metal screws hold the heating element in place very easy to remove.. upon removal you will have plenty of room to pull element out and switch out the wires you need to do.. Upon examination I think my trouble was a high limit fuse that burned out, so I propably did'nt need to buy the whole element ( you might want to check that first it is the ceramic one ) cleaned everything out and dryer is as good as new Good luck

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

did basic diagnostics to narrow down the problem to be likely one of the three parts include w/ the kit. removed front panel and confirmed that part looked like the one on the web page. part arrived 3 business days after ordering.
used nutdriver to remove two screws holding old part in place. pulled old part out still attached to wiring harness and assembled new part and attached wires the same way as the old part. installed new part, plugged in dryer and confirmed that it was heating. replaced front pannel and dryer is now working as well as ever. hardest part was reaching to the back of the dryer from the front while lying on the floor. total cost was cheaper than a service call, let alone paying for parts and labor from a service tech.

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

Just follow the video. The hardest part is getting the top to disengage from the clips.

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

The dryer was squealing, so I looked videos on how to take the dryer apart. After I got it apart, I spun the roller wheels, the motor, and the idler pulley, and only the idler pulley gave an indication that it was sticking or not spinning appropriately, so I ordered the part and replaced it. And sure enough, it was the problem after all!

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!