MDE6400AYW Maytag Dryer - Instructions

Opened front of dryer & watched the heating unit not shutting off. Purchased the proper high limit thermostat. Replaced it and the multi-temp cycling thermostat for good measure. My dryer runs like new with no additional problems. Thanks for making parts so readily available. Thought I was going to have to replace my dryer, but now it's fixed.....Thanks,again.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

After changing all the rollers in the dryer (which didn't fix the problem) I decided to take apart the blower. Sure enough, that was the problem. As the dryer heated up, the damaged wheel would swell and start rubbing the housing. I replaced both and fixed the problem. The repair was pretty easy, since I had taken the dryer apart several times replacing the rollers.

We tried replacing the door switch first, still didn't start. Next we tried the thermal fuse and it turned on and has worked ever since.

popped out old female clasp on dryer itself with screwdriver, undid 2 screws on dryer door and door handle with phillips screwdriver, popped in new male clasp part, put door knob back on and put the two screws back in door and it was all set to go. Less than 15 minutes to do. Better than new and wife is happy. No more duct tape holding door closed now.

Well, I had to find out just how the dryer came apart. Most of the time, the back comes off but with this particular Maytag, it is the front that has to be removed. Once the four screws from either side are removed, the front pops off and the canister that holds the heating element is right there on the bottom. Cleaning away years of lint was fun but the heating canister was removed quickly using two screws and removing four wires that attached to the unit. Once the screws were removed (top back and bottom front) and the wires removed, the replacement unit slid right in without any problems. The regulator on the old unit had to be transferred to the new unit before installation. I closed up the front, put the four screws back in and snapped the front closed and the dryer worked perfectly.

pulled the motor and replaced it and not having any issues since.

Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

replaced timer and pull knob. easy and work great.

removed the 3 screws holding the front cover on to the timer, unsnapped the timer, unpluged it and plugged in the new one then snapped it back in place. put the front cover back and placed the timer cap back on it works like new now and saved me $140 dollars. Very happy to not look like I am trying to extract a tooth when turning on the dryer

My 11 year old grandson and I did the repair together. He had a blast and I did too. First we removed a bunch of screws that got us no closer to getting the machine apart than when we started. Then I remembered from the last time I had the machine apart that there are two screws just below the door, angled as not to be visable unless you know where to look. Once we removed those the from came off. We removed the wires for the door light and heat sensor, remembering the order of the wires for later reinstallation. Then we undid the bolts holding down the top. Once the top was removed we took off the belt and removed the drum. We used the retainer pliers to remove the retainer ring from the first roller. We removed the roller and also the shaft as this roller was the noise maker and the shaft was not in reusable condition. We installed a new shaft, roller washer, roller, another roller washer and then the retainer ring. We repeated the same process on the other roller, although we did not replace the shaft as it was in good condition. It turned out I did not need to order the shaft washers as the rollers came with washers. Oh well, its not a good job unless you have parts left over when you are done. Once we replaced the rollers we commenced reinstallation. But first we had to google for diagram of the proper belt installation, which we found and that got the drum and belt installed properly. Thankd god for the internet. Once we had the drum installed we put the machine back together in the opposite order we took it apart. An operational test showed we did the job right, no more squeaking. The only injury was my grandson cut his thumb right after I gave him the speech about watching where your hand is going to end up when that bolt breaks free. It broke loose and into the metal bracket went his thumb. Oh well it was a good lesson and it was not a bad cut. All in all a good repair.

I took out screws holding top to dryer & raised the top & proped it up to gain access to inside of the dryeeer drum. I then inatalled the new baffle & secured it with 2 screws. It would have been better if the part came with new screws.It was hard to determine which was the right screws for this application.

Piece of cake. Used flat screwdriver to pry out female part on cabinet side, same with the male part on door. Every new replacement part was tight and operated like new. Thanks Part Select, you'll be forever on my list of online parts buying.

When the timer was pulled out to start the dryer it would not consistently start up. I generally had to wiggle it around to get the dryer started.

I replaced the timer. To do this you need to pull off the front cover of the timer knob with a small screw driver I then used a needle nose plier to sqeeze together two pieces of plastic that hold the knob in place. The knob is then removed.
Next, there are three screws at the top of the dryer that need to be removed to take off the front cover to the instrument panel.
Removing the old timer is easy. Take off the wiring harness. In removing the harness, there is a small tab that needs to be pushed down.
To remove the old timer, there is a small tab on the instrument panel that holds the timer in place that needs to be pushed down. From there it is easy to slide out the old timer and replace it.

Removed the dryer front, then detached the retainer ring holding the blower wheel in place. Set the new blower wheel, attached the new ring retainer and placed the dryer front back in place. Thank you for the low prices - I searched on-line at 3 sites and you were the best price available.