ADE20L2H Admiral Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from Northfield, MN
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
looked at heating element saw wire was broke
Took less than five minutes to fix a couple screws and take some wires off and pull it right out. Called local apliance store if they had part wanted more than partselect with next day shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Leetonia, OH
- Parts Used:
- WP53-1182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the dryer would not run, found the thermal fuse blown
Remove and replace thermal fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Winter Springs, FL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
dryer would not start
watched available video on site removed 4 screws all at top of washer. had to replace heater element, thermostat and thermal fuse. very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vivian from Dix, IL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer running, but no heat.
Unplug the dryer. Take a large flat head screwdriver and pop the hood loose from the retaining brackets on the front of the dryer and raise.Next, unhook the wiring from the thermostat and heating element with needle nosed pliers located in the back left corner. Use a 5mm socket to remove the thermostat bracket and the heating element bracket.Remove faulty part and replace. Replace heating element and tighten.Replace thermostat on the retaining bracket and tighten. Plug your wires back in and close the hood.Plug Dryer back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from Raleigh, NC
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heater coil broken and shorted out against wall.
just like the training video showed, and was very happy at how it came fast, installed easy and back in the drying business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from Kissimmee, FL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
unit was working but not heating
After lifting up hood, my husband removed old part and installed new part 1, 2, 3. Took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dillon Beach, CA
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
No heat
Disassembled the dryer- pretty simple process, replaced the heating element and high limit switch (which was included with the heating element), put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Fenton, MO
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Extended drying time
Unplugged dryer from electrical outlet, lifted up top of dryer, removed overheating sensor and dryer element with 1/4"socket being very careful not to drop screws into dryer, replaced dryer element and heat sensor, closed top lid of dryer, plugged back into outlet and tested for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Pearl, IL
- Parts Used:
- LA-1008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud noise
replaced belt first didnt fix the noise so i replaced rear drum support roller kit and that fixed the noise this was a cheap fix cost me about 70.00 dollars verses a new dryer thank you your website was a big help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Merrillan, WI
- Parts Used:
- LA-1008
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
left roller support shaft has flat on one side
1.used small flat head screw driver to pop top of dryer. 2.used phillips screw driver to remove front of dryer. 3.disengage dryer belt. 4.take hold of brum and turn and pull out. 5.{left side}take snap ring,washer,roller off then remove support shaft. 6.install new parts, support shaft,roller washer, snap ring. 7,right side has a plastic washer that goes on before roller rest will be as step 5 8.put dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from North Smithfield, RI
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer belt broke
took the dryer apart noticed it needed a belt and rear drum supports. Ordered the parts(they were very helpful on getting the right part . they came in very fast (less than 24 hours). replace the broken parts. The dryer is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Baton Rouge, LA
- Parts Used:
- W10410996
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
motor burned up
I'm an ex auto mechanic so I'm pretty good w/my hands. I just followed your instructions on a video you provided & it was really easy. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Irvine, CA
- Parts Used:
- WP53-0771
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer would not start and interior light was not on
I opened the lid and using the Nut driver removed the old High limit Thermostat.Then repalces the new one, replaced the lid and plugged in the dryer.It still did not start.I then found the fuse hiddden on the side of the heater element, testd the fuse on it was blown. I placed an order for the fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Cary, NC
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers
Squealing noise
Followed directions on movie. This was a simple process. Although in the end I found that replacing the rollers was not the problem in the end. It turned out to be the motor, which I was able to repair with some prior experience with electric motors and a bit of oil. That's why it took as long as it did to make the total repair. Still happy with the outcome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from GOLD BEACH, OR
- Parts Used:
- 12002126
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
when we were cleaning the fan we discovered the teflon coated guide had broken
the hardest part of fixing it was getting the belt off the roller guide. the actual part was easy to fix
Was this instruction helpful to you?
Thank you for voting!