ADE20L2H Admiral Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sarah from Bristol, IN
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Heating Element
It took longer to gather the tools vs changing the part. I was unsure how to start. Once I got started it was very easy it took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Kosciusko, MS
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No Heat
UNPLUG DRYER!!
1)Opened top with putty knife pushing on the two spring clips.
2)Removed Hi Limit switch w/bracket (1 screw)
3)Removed Old Element (1 Screw)
4)Installed New Element
5)Replaced Hilemit Switch on bracket (2 Screws)
6)Reinstalled Hi Limit switch/bracket
7)Reinstalled wires/Closed Lid/Plugged In/Started Up....No Problem
1)Opened top with putty knife pushing on the two spring clips.
2)Removed Hi Limit switch w/bracket (1 screw)
3)Removed Old Element (1 Screw)
4)Installed New Element
5)Replaced Hilemit Switch on bracket (2 Screws)
6)Reinstalled Hi Limit switch/bracket
7)Reinstalled wires/Closed Lid/Plugged In/Started Up....No Problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Jarrettsville, MD
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
no heat
It was very simple thanks to your notes on line
I would use your site for ordering any other needs I have.
Thank You
Robert
I would use your site for ordering any other needs I have.
Thank You
Robert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Roswell, GA
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer doesn't heat
I used a butter knife to push the spring clips that hold the top down, this was the hardest part of the repair. Once the top was open it took about 20 minutes to pull out the old part and replace with the new, including running the dryer on high for a few minutes to get rid of the new element smell. Always unplug before attempting any electrical work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Meriden, CT
- Parts Used:
- 53-1758
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
SPARkS CAME FROM THE TIMER
Unpluged the dryer and removed the rear cover to get access to the timer. Removed the control panel and unscrewed the timer leaving the wires connected. One by one connected the wires to the new timer along with the resistor. Secured the timer to the control panel and attached the control panel and rear cover. If you have enough room you do not have to remove the control panel.
The dryer works great.
The dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Opelousas, LA
- Parts Used:
- 530106
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Blower wheel broke off of shaft.
Purchased a new blower wheel from you and installed.
The part was exactly what I needed and was delivered ahead of schedule. Ordering over the internet was easy and straight forward.
The part was exactly what I needed and was delivered ahead of schedule. Ordering over the internet was easy and straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Florence from Center Point, TX
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer Element Not Heating
Daughter and I lifted top of dryer, carefully removed old element and thermostat, watching as we went how the old ones came out, and replaced with new one! Dryer working just fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erik from Lancaster, PA
- Parts Used:
- 530106
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer would not dry the clothes
t
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Alpine, TX
- Parts Used:
- LA-1044
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Heating element in dryer went out
Opened up the top of the dryer. Had to use the internet to find the broken part since the last time I replaced a heating element it was at the bottom. This one was at the top behind the drum. Disconnected three screws holding the old element in place and the wiring. Pulled the old element and put the new one in replacing the wiring and the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loretta from Manassa, CO
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer won't heat
Contrary to instructions that I found on the web, the element is not accessed through the back. Pop the top of the dryer up and the element is visible in the top of the back . Pretty easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marty from Sterling heights, MI
- Parts Used:
- W10410996, 31001465, WP31001344
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Squealing Berring
I had to replace the whole motor, Idler spring and idler Pulley Wheel. It went well but I wish I could have replaced just the berring and not the whole motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Dysart, IA
- Parts Used:
- WP53-1182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer would not start
After I unplugged the unit, I used a flat screwdriver to pop the top open at the front, then tipped it back on the hinge. I then used a multi-meter to test resistance through any switch or safety device I could find. The thermal fuse was the hardest one to get to and was the only one that showed open, having no resistance. I had to remove the screw that holds the heating element in place and carefully slide the element out of the way. The fuse is held in place by a metal strip or retainer and it has to be lifted up and right as you remove it. Unplug the wires from the old fuse and put in the new one. Then reverse the order of dis-assembly, plug it in and away you go, as long as that is the only issue, which mine was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from PILOT HILL, CA
- Parts Used:
- LA-1044
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer not working, belt broken
1st replaced the broken drum belt, then the heating element failed, ordered a replacement, arrived over night thank you very much. Installed new heating element, 5 minutes later the motor failed. Bought a new dryer, ate the heater element as it is now used.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from West fork, AR
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer not warming
Found the heating element under top of dryer towards the back and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nyssa from Severna Park, MD
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drying not heating/drying clothes
I unclipped the top of the dryer for access to the heating coils. I unscrewed the bracket holding the high limit thermostat (the heating element was directly below the high limit thermostat). I removed one screw holding the heating element in place, and then removed the faulty heating element. I checked the old heating element and the old high limit thermostat with a multimeter to confirm that they were faulty - both the heating coil and the HL thermostat had continuity but the coils looked like they needed to be replaced (not rusty, but dingy). I installed the new heating element and the new HL thermostat, closed the top of the dryer and ran the dryer - it worked :) Thanks partselect.com!
Was this instruction helpful to you?
Thank you for voting!