ADE20L2H Admiral Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Baton Rouge, LA
- Parts Used:
- W10410996
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
motor burned up
I'm an ex auto mechanic so I'm pretty good w/my hands. I just followed your instructions on a video you provided & it was really easy. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Cary, NC
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers
Squealing noise
Followed directions on movie. This was a simple process. Although in the end I found that replacing the rollers was not the problem in the end. It turned out to be the motor, which I was able to repair with some prior experience with electric motors and a bit of oil. That's why it took as long as it did to make the total repair. Still happy with the outcome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from bend, OR
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Dryer stopped drying cloths out of the blue. Everything work fine but no heat.
I watched a part select youtube video on possible fixes for the problem I was having. Ten minutes and two videos later I had the part out and identified as the problem. I ordered the part ($42.00) which arrived four days later. Spent ten minutes replacing it in machine, turned dryer on and went right back to performing the way it has for the last 12 years. Easiest thing I did all day. Saved me $400 bucks too. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Northfield, MN
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
looked at heating element saw wire was broke
Took less than five minutes to fix a couple screws and take some wires off and pull it right out. Called local apliance store if they had part wanted more than partselect with next day shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Irvine, CA
- Parts Used:
- WP53-0771
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer would not start and interior light was not on
I opened the lid and using the Nut driver removed the old High limit Thermostat.Then repalces the new one, replaced the lid and plugged in the dryer.It still did not start.I then found the fuse hiddden on the side of the heater element, testd the fuse on it was blown. I placed an order for the fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Lamar, MS
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Element was bad and wasn't heating
I watched your video and it was exactly like you guys said. You truly have a great site and I will tell all my friends about it. Great service, can't say enough about how pleased I am with your site and service. Saved me a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leona from Colorado Springs, CO
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Noise in dryer when first starting up
Turn off power. Move dryer away from wall and release the top by lifting up to release the two clips. Lay top against the wall. Remove the two screws, one in each corner, left and right inside the cabinet. Lift front panel up and out away from dryer. Place along right side of dryer. You may need to unlatch the wiring for the door switch. Reach inside the bottom of dryer and release the belt. Lift the dryer drum out along with the belt. Observe the two guide rollers that the drum rides on. Using a blade screw driver release the clips that hold the rollers onto the spindles. Clean up around each spindle. Install new rollers in reverse order and put all back together. The hardest part is reinstalling the belt. Put belt around the drum, around the motor pulley and then onto the tension roller. Good luck..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from Kissimmee, FL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
unit was working but not heating
After lifting up hood, my husband removed old part and installed new part 1, 2, 3. Took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!