66512776K310 Whirlpool Dishwasher - Instructions

On my kitchen counter! Repair was relatively easy. New adjuster appears to be substantially stronger than old!

While watching my infant daughter! The information strict ions and illustrations made my repair go easily. I removed the old parts and replaced the parts with ease.

Found replacement instructions on the Internet and followed them to replace the left side rack adjuster. This was very easy but took the longest since I had never done it before. Right side literally took a fraction of the time since I had already done it once!

Removed broken adjuster by prying open latch tabs. Assembled replacement per instructions. Had to test fit parts due to poor illustrations, compared to other adjuster for correct installation. 2nd side went much quicker

I removed the old worn parts completely and then, following the instructions and trying to look at the pictures which were very dark and not able to be seen very well, I put the new parts on and replaced the rack in the dishwasher. The repair was fairly simple but would have been easier if the pictures on the instructions had been better.

Took a bit of interpretation to figure out how the piece fit together. Not same as the original. Once i decoded the system, the second side took less than 10 minutes. Fits and works fine.

removed old basket adjuster -installed wheel assemble-installed clips to hold wheel assemble installed adjuster on basket installed final adjuster part with screws supplied--instruction photos not clear and to small -first side took about an hour-the second side took ten minutes -parts work great-anyone with common sense can do the repair

tried to follow the instruction that came with the parts, to no avail? it would have been better to send a note that said good luck. the only part that helped was the part that said remove the old parts. after that is was just a fit and test, fit and test, fit and test, only because of my expert analytical abilities was i able to fit it all together. please draw up better instructions. it fits good and works well.

Remove old rack adjusters. No removal instructions. Do one at a time. First requires some trial & error until removed. Install new replacement. Instructions not clear because pictures are dark & fuzzy. Again, install one with some trial & error. Second remove & replace becomes very easy.

I disassembled the left side, and installed the new assembly. However, being older and my eyesight not the best, and had assembled it slightly out of position. After adding more light, a magnifying glass. and a much closer look, I found my mistake. I reassembled the unit. The right side only took about ten minutes. I would recommend a larger more visible picture of the unit. I noticed that the units did not roll as easily as the old ones. One must give a slight push to engage the tray into the back of the dishwasher. Had the picture been better, it would have taken only 20 or 30 minutes to assemble.

I had left one adjuster on but the new ones were different. I started great but when doing the top part I didn't line up the wire rack with the holes in the upper adjuster plate and found out it was wrong so I had to use the pliers to unsnap the metal piece where they lock in. Once I got the first one complete it only took about 5 minutes to do the other side. The pictures included with the installation sheet were very dark. A you tube video would have been a great asset. It would have made it very simple and easy. In truth, the second side should only take a minute or two because I was only using one hand. My other arm was in a cast because I broke it. Anyone could do this.

Followed the enclosed instructions.

Removed all the old adjuster parts. Laid out new parts for each side. Would have helped if pictures had been better quality. Figured out how the parts would be installed before actually installing them. Almost messed up 2 plastic tabs by not understanding how 2 parts locked together with the tabs and shoved them together too far on the trial run but, was able to get them apart without breaking off the tabs. The new parts are a stronger design than the original. The tracks work like a dream. I rated it a "Bit Difficult" because in the pictures I could not see enough detail, otherwise I would rate it easy.

I went on line as instructed by one of your representatives and found clear instructions how to remove old part and put on new one. It was an excellent presentation. It can be found at w10712394 instructions

I looked up a you tube video of replacement for model and part. the video gave consise, clear and easy to follow directions. Using the video it took about 15-20 minutes to easily do the job.(I had difficulty seeing photos and reading printed directions that accompanied the part.)