WDT530HAMM0 Whirlpool Dishwasher - Instructions

Thank you for letting me share my repair experience with you.
I removed the two screws that hold the diswasher to the wooden cabinet. Lowered the leveling adjustment screws on bottom of unit, then slid out the diswasher from inside the cabinet.
Then ordered the new lanyard. Waited one week day and the order arrived via mail. It has two lanyars and new rotating pulley assemblies for both sides of the door. I loosened the bottom screw on the old pully assembly and refitted the new pulleys in same location. (very easy). I then refitted spring to back of unit (with blue line toward front), then fitted the lanyard to the spring. Pulled lanyard thru the pulley. Had to have nice wife connect the other side of the lanyard to the post as I extended the spring on the side of the unit. We completed same steps on other side of the unit. After completing the door lanyard repair, I slid the dishwasher in the cabinet, re-leveled the unit with the front adjustment screw, then incerted the cabinet screws into the wooden cabinet. I feel this was quite a savings to us. Thanks to nice individuals on the internet and partselect.com, who provided excellent service to me....and my family. I also can see the end result of my effort, which is a nice feeling.
Thank you.

First we removed the two screws up under the countertop that secured the dishwasher in place. Next we pulled the d/w out from under the counter, having to unplug the power cord and feeding the drain hose into the d/w cavity from under the kitchen sink to allow this. On each side, attached to a metal spring was a nylon cord with plastic attachments that ran through two plastic pullies/wheels. The plastic piece on one of the nylon cords had broken...only on one side, so we were able to just look at the 'good' side to see how to attach and string the repair part through again. We pushed the d/w back in, made sure the drain hose under the kitchen sink wasn't kinked by pulling it back under the sink from the d/w cavity, plugged it in, replaced the two securing screws and were done. The old cord running through the pullies had always creaked when the door was opened, so while the d/w was out, we coated it w/ WD40. Piece-of-cake!

The door balance springs are connected to the door via a nylon cable which snakes through a couple of pulleys. The plastic fastener on the end of one of these cables separated, so the one remaining spring was not able to offset the weight of the door. Easy to fix, just slide the unit out about 15 inches (remove base plate, and undo a couple screws on top) then replace cables. You can buy just the one cable, or for a couple bucks more, both L&R cables and new pulleys. Replaced the pulleys on my unit at the same time (remove one screw and twist out) since the replacement parts were of better quality than my factory parts. Don’t pay a repair guy $250 or more to fix this for you. It’s easy.

Followed directions here. Extremely easy repair.

First I turned off the water and power to the dishwasher.I removed the two screws on the front bottom cover plate, removed the plate. Removed the two nuts and bolts holding the dishwasher in place between the cabinets. Then I pulled the dishwasher out about 6 to 7 inches so I could see the spring, pulley and rope connections. Then I saw the rope on the right side of the door bottom had pulled through the connector. I ordered the part and next day delivery was great.(excellent service). The repair kit comes with both sides parts but I only needed one(for now). I reconnected spring to rope connector and threaded through pulley and to the door and job was done. A little difficult stretching spring so I put a long piece of wire to hold spring tight while connecting to rope but I worked out great. My husband said "great job, honey". I saved a $150 repairman bill....now I might go shopping (ha ha) Kim

Removed the bottom cover plates.
Removed the screws holding in the dishwasher.
Removed old single moving roller and replaced with newly designed double rollers.
Installed link(string).
Replaced other side rollers and link.
Reinstalled dishwaser.

You said the repair was easy and would take around 5 minutes to perform. You were spot on and the instructional video really helped do the job.

pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.

Just like the video; remove the 2 nuts off the kick plate, remove the 2 screws under the counter, pull the unit out, ease the spring off the cable, nut drive the pully assembly's off, install the new ones, place new rope/cable from the door arms onto pullys, attach the spring, push the unit back into place, replace screws and the kick plate. Took 15 minutes.

followed your very well done video clip exactly.

After pulling the dishwasher out of the cabinet (2 screws held brackets to the underside of the counter - accessible when the door is open), I removed the broken link pieces, re-attached the springs and routed the link line around the pulleys. No need to re-set the spring tension as it was adjusted properly.

Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary.

I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.

Removed 2 screws that held unit under counter. Slid diswasher out about half way; reattached metal spring in back and removed broken string. Attached replacement string to spring and threaded through wheels (copying other side), then attached string to door. Tada! Done. Will never pay a call-out fee again (for this problem anyway...)

Turned off power to dishwasher.
Removed screws from dishwasher retaining clips.
Pulled out dishwasher.
Removed broken rope.
Installed replacement and put everything back together.
Very easy repair. The spring is very strong and extra hand can be helpful, but not required.

First I removed the two screws holding the dishwasher in place. Then I pulled the dishwasher forward from under the counter about 2 feet, attached the new part to the spring and pulley, then pushed the dishwasher back into place and installed screws.
PartSelect was awesome! UPS delivered to the wrong address and Partselect took care of it IMMEDIATELY! I have ordered more parts from them and no problems. I would DEFINATELY recomend them!

Remove power. Remove drain line from sink. Remove hot water line at connection. Remove 2 screws that hold dishwasher to countertop (on top). Pull dishwasher out. Find spring as it has shot to the back when the nylon cord link broke. Hook Spring back in. Attach cord loop end (hard plastic) to spring. Attach other end to door hook. Now stretch spring to loosen cord and slip around pully system. Push dishwasher back in and rehook all connections.