WDT530HAMM0 Whirlpool Dishwasher - Instructions

Hardest part of job was sliding dishwasher out. Put in wood floors so limited free space. Had to lower fron foot pegs first, then remove 2 screws from top that held unit steady. Once dishwasher was out a good 16" cords were easy to replace. Did not replace bracket that came with kit. Cords attach to heavy duty spring.

My husband managed, with some difficulty, to finally replace the broken spring and associated door balance kit. He first ordered the spring from this site. Then, after he had laboriously rolled the dishwasher out about 12" - using flat pieces of wood as support, while he lowered the dishwasher onto his homemade rollers - he realized that the corded door balance kit was also broken. So he rolled the DW back in and ordered the part. This site sent an improved door balance kit, and then he went through the same process again. He had to fish the spring back all the way to the very back of the DW and hook it through a hole, using a rod and masking tape (bad DW design, he says). Then after he rolled it back, he noticed a leak in the incoming hot water connector, at the copper pipe compression fitting. Fortunately, a local plumber, with the right tool and expertise was able to quickly fix that problem. (The plumber explained that compression fittings commonly begin leaking if even slightly moved.) Bottom line: A+ for this site, C for KitchenAid design. He says he'd undertake it again, in spite of the hassle.

remove the bottom plate with a nut driver and back off on the front leg adjusters. Slide out the dishwasher approx 8-10 inches and remove the broken link. The new one goes on easily. Look at the opposite side if in doubt as to how to attach. Slide the unit back in and tighten the leg adjusters until the unit is secure. reattach the lower front panel which hides the leg adjusters, etc. You're done!

Pulled dishwasher from under the counter and replaced the plastic part with the new part and attached the new cord to the door spring and to the replacement plastic part. replaced the dishwasher under the counter and replaced the kick plate. All Done.

Started the rope onto the top holder, threaded the rope around the rollers and using the pilers pulled the spring forward to attach the other end of the rope.

just move the machine out and replace the string. this site is very reliable and and great company. since the dishmachine door cannot be closed, we first order door strike, ,,,, still doesn't work after installation. and return all parts and order the balance kit, now works fine after. we appreciate your help

1st pull dishwasher out. attach the new cable to the spring. reinstall the spring on the frame. Use pliers to pull slack in the cable to attach the cable to the door. The hardest thing about the install was putting the screws in the side of the dishwasher to the cabinets.

Shut off elec. and water. remove bottom plate and 2 screws holding the unit to the counter top.
disconect elec wires to unit and remove water line.
Pull unit out from counter and replace cable to spring the same way as the unbroken side.
Slide unit back and reverse hookup.
My only problem was that the part they sent me was about a 1/2" shorter the the original and the door is hard to open.

The repair itself was relatively easy. I basically only had to remove the two screws that were securing the diswasher to the cabinetry, disconnected the water line and extended the diswasher out approximately 10 inches. I then replaced the part by hooking the new cable assembly to the spring and using pliers expanded the spring so I could snake the other end of the cable through the pulleys and attach it to the door. The otherside was my guide. This part should be modified to replace the two plastic ends with metal counterparts. This would allow the part to have a longer life especially in my case since the plastic end broke and not the cable itself.

Received the part. No instructions came with it. Luckily it was pretty simple to figure out. i removed the appliance from under the counter, saw how the part was attached on the other side and simply replaced the other side that was broken. Easy.

Disconnect top screws
Pull dishwasher out halfway
Notice how the other side is connected
Thread cord, use pliers to pull spring to connect.

I pulled the dishwasher out just over half way to access the spring area. Unscrewed the old assembly and screwed the new one in it's place. Attached the string line to the spring, wrapped it around the assembly and attached it to the door hook. Repeated procedure on other side. Problem solved.

Pulled dishwasher and removed existing springs and attached rope. Ordered the part needed and replaced it somewhat easily. There is a lot of tension because of the spring on the door. Once part was installed we were ready to use our dishwasher right away. Even though the rope was broke on only one side - we replaced both sides.

Pulled out dishwasher to access the sides. Removed onld lines and then unscrewed pulley from frame using socket / nutdriver. Replaced pulleys with new units supplied in the kit and then threaded new lines onto door and springs. Repair complete in less than 5 minutes.

Followed the parts list diagram and confirmed with the link on the other side of door. Hooked the plastic attachment to the door, threaded the string around the plastic pulleys, attached the spring and mount it to the back of the dishwasher. that was it! Very easy to do. Hardest part was sliding the dishwasher out and in.