WDT530HAMM0 Whirlpool Dishwasher - Instructions

repaired exactly as your video described......hardest part it getting unit out from under cabinet and back in.

Pulled the dishwasher out and removed the plastic pulley on the bottom of the unit. Installed the new pulley. wrapped the string assy. around the pulley and attached it to the spring and reinstalled it to the back of the dishwasher. We discovered the front bracket on the dishwasher door was bent slightly causing the string to rub and probably is what caused the string to break. We bent the bracket back into shape and reinstalled the dishwasher in its cavity.

Followed a repair video.

Replaced door balance link kit and door opens easy does not squeak or slam down.

Video was great help. Replacing the balance parts was easy. My wife and I are in our 80's. Mobility is difficult when it comes to working on the floor. Between the two of us we spent the majority of our time just getting up and down,

Ordered the part. Called my son who brought over his toolkit. Played him the repair video on my iPad and he replaced both Door Balance Links. Door works great now.

Pulled dishwasher from under the counter and replaced the plastic part with the new part and attached the new cord to the door spring and to the replacement plastic part. replaced the dishwasher under the counter and replaced the kick plate. All Done.

Remove two screws then the two toe-panels. Use a flashlight to locate spring and the hole in the metal frame near back of unit about an inch off the floor. Look at opposite side of unit to see how the working link is routed. Place correct end of the link over one end of the spring and wrap a piece of tape around nylon clip and spring end (just to save frustration of having it fall off while you attempt to complete this task). Tie a loop in the end of each end of the piece of string you supplied. Loop one loop around the spring end with the link clip and feed the other end of the strings loop out the front of the dishwasher at the bottom near the lowermost pulley. Reach under the dishwasher and hook the spring to the frame. Keep tension on the string and feed the link cord out the front of the dishwasher near the front bottom near the lowermost pulley. Loop the exposed end of the self-supplied string around the center of the flashlight handle. Have an assistant pull firmly on the flashlight/string stretching the spring (not too much to over-stretch the spring, but give yourself a little slack too). Serpentine the link cord around the two nylon pulleys. Make sure the rope side of the link clip is toward the back of the dishwasher. Place the link nylon clip over the metal door lever and into the appropriate slot. Have your assistant slowly release tension on the spring/string. Reach under the dishwasher and remove the looped string from the spring end and remove the string. Replace the toe-panels. I did the right side this way, the left side is up against a wall and I might have had additional problems, but it is hard to say since I did not replace the left link. I thought this easier than removing the dishwasher, inlet and outlet as I have done that several times and it can be a pain as well. Good luck!

The hardest part was pulling the unit out. Ours required the electric to be disconnected. First turn off breaker, then disconnect electric, then remove the 2 screws in the sides that keep it in place (located on top for non-stone counter). Slide unit out. Next remove the spring and connect the loop from the link to the spring. The other end of the spring goes in the hole next to the rear leg. Pull the string so there is enough slack to loop the spring aroung both pulleys and then slide the end over the hook on the bottom of the door. Use the other side as a guide. Slide unit back, hook up electric, replace mounting screws. Turn on breaker.

For some reason I wasn't able to pull the dishwasher all the way out. Had my wife with a smaller hands and arms reached in and attached the spring with the link end onto the dishwaster anchor point. I then put on both nylon rollers. The link anchor point and rope went over the upper roller first. I then struggled and managed, with lots of pulling, to get the rope over the lower nylon roller. All went well with reattaching the water and drain lines. Plumbing in tight spaces is made for small people. This old body does not bend like it use too.
.

last time this piece broke, I called a tech and $150 to fix. I am not much of a do-it-yourselfer, but this was very easy. Removed to screws. I then pulled out dishawasher from cabinet. Removed plastic piece, replaced part, pushed dishwasher back and put in screws.

Easy, easy, easy. Appliances use to be built with metal parts that did not break as often.

We pulled the unit out and were able to easily see where it broke. We replaced it relatively easy, pushed dishwasher back in; however, somehow the pump seal got broken in the process so now we have to replace the pump. This was totally unrelated to this repair - only can assume it happened when we pushed the unit back into place.

Fairly easy. Undid the two screws on the kick plate. Then used pliers to undo the leveling legs and pulled the dishwasher out from under the cabinet. The dishwasher is hard-wired with extra electric cable. The drainage tube is flexible and there is extra so I did not have to worry about disconnecting anything. I then attached the new door cable link to the spring. Using the Needle-nosed Vise Grips I pulled the cable so I had enough to make the connection on the door piece. Done. Then I put everything back.

My 2 yr old sat on the dishwasher door while it was open. It snapped both the links on the door causing the dishwasher door to drop every time it was ajar. It was a real danger to the kids or to anyone else unaware of the door given its weight.

I ordered the part from Part Select based model and some of the posts that it was something you can do yourself. Park Select was outstanding as got the part next day and got direction from others (thank you). I did not have either side of the door working so no real gauge but finally understood how it worked once I did a search online for a picture.

Recommendation: if both links (rope) are broken, you will need to hunt down the springs on side/back of machine. The part with small hole connects to the spring, the other to the door. Make a reverse S with the rope through the pully system for tention. I did not initially do the reverse S and the part popped of the door once I closed it. Otherwise, easy thing to do and certainly do not need a repair person.....if you need picture, do a search on dishwasher door pully system

Hardest part of job was sliding dishwasher out. Put in wood floors so limited free space. Had to lower fron foot pegs first, then remove 2 screws from top that held unit steady. Once dishwasher was out a good 16" cords were easy to replace. Did not replace bracket that came with kit. Cords attach to heavy duty spring.