5871434969 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matt from Salisbury, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
(leaking) heater element nuts cracked under dishwasher
power off, take off kickplate, unplug 2 wires and unscrew broken nuts, put new nuts on, plug wires back in,(run dishwasher one cycle to make sure no leaks) put kickplate back on, power on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from San diego, CA
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dishwasher door strike broke.
I just pulled the insulation from the top of the dishwasher back enough to expose the screws holding the door strike in place, unscrewed the broken part and replaced it with the new one. It was that simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Boscobel, WI
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher door was leaking.
Pulled out the gasket,trimmed the gasket to fit and alittle pressure to put.it in place, very easyto do. No worries any one can do this and savek yourself costly repair person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from Chandler, AZ
- Parts Used:
- 154637401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Leaky inlet valve
Cakewalk, replacing a water inlet valve is self-explanatory. Take the old one off, put the new one on .. that's pretty much it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Conway, NC
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
door strike broken
Unscrewed dishwasher from cabnet. Removed nuts holding old strike in place. Put new strike in place and then reattached bolts to hold strike down. Followed by reattaching dishwasher to cabnet. Ready to use
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cody from kalispell, MT
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaking aroung the door
replaced gasket easy-peesy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from South Park, PA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original rack wheels where bent and upper wheels had melted
husband replaced wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Roseville, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water discharge (around door) during Wash Cycle
After reading some "Suggested Installation Instructions" on the Parts Select Website, I felt at ease tackling this job. After opening the door, I simply pulled-out the existing door gasket. The installation involved simply pressing in the new gasket with my finger and insuring it was properly seated. The only tool I had to use was a pair of scissors to cut the excess length as I pressed it in. REALLY APPRECIATED THE SIMPLE INSTALLATION INSTRUCTIONS as I had never done this particular task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Matthews, NC
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Original cast door strike broke off flush with frame
I unbolted the diswahser from the cabinet, slid it forward about 6", removed two small screws, switched the new part (better made than original-not a cast part)for the old and buttened evrything back up. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hammonton, NJ
- Parts Used:
- 154827601
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Leaking at the door
I just pulled the old one out and installed the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Pine Grove, PA
- Parts Used:
- 154637401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Water inlet valve failed and leaked.
Turn off water supply to dishwasher. Turn off electrical power to dishwasher. Remove lower front cover to expose underneath the unit. Locate the valve toward the left, front underneath the washer. unplug the wire harness from the valve. lay a towel under the valve to catch water that WILL come out. Using a pair of needle nose pliers, squeeze and slide back the hose clamp holding the hose to the water bottle. Remove the 2 screws that mount the valve bracket to the frame. There is plenty of slack in the braided water feed hose to pull the valve out from under the washer. Remove the hose from the fitting and then remove the fitting from the valve. Re-wrap the threads of the fitting with teflon tape and install into new valve. Attach and tighten the braided supply hose to the fitting. Install the valve in reverse order of removal. It takes about 10 minutes to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Sanbornville, NH
- Parts Used:
- 154637401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
did not fill with water
I unscrewed the kick plate took out the old part replaced it with the new one .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronda from Monkey Island, OK
- Parts Used:
- 5304523457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
water intake tube had been chewed by mice
very simply removed 2 clamps, replace hose, re-installed clamps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from El Paso, TX
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the tub was leaking at the right front corner
just pushed it into the crevice with my thumb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dunstan from Port St.. Lucie, FL
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leak at bottom of door
Remove old gasket from tub, soak new gasket in hot water for a few minutes then install starting from center top of tub, when done installing close door for 24 hours, then try to see if leak fixed.
Was this instruction helpful to you?
Thank you for voting!