66513932K014 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Earl from Youngsville, LA
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Stops broke
Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Abby from SACO, ME
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Door would no longer latch
cut power to dishwasher. removed screws all around door panel to get front panel off, leaving top two screws for last. unplugged latch set, removed it. set new one in. screwed top 2 screws in. fit door panel back on. pulled out latch hook from stationary top piece and clicked new on in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from DREXEL HILL, PA
- Parts Used:
- W10619006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Top rack adjusters fell apart and would not slide back and forth.
I followed the Partselect video for the new installation. Very easy to follow which made new part installation extremely easy. Works perfect now!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from REIDSVILLE, NC
- Parts Used:
- WPW10195623, WPW10195622
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Installing the rack stop clip was, at first, very difficult, if not impossible.
Stared at it and deduced that the clip was not intended to slide into the track from the end, but that it was intended to snap in from the side. NO WHERE WAS THERE A SINGLE SENTENCE TELLING HOW TO DO THIS. And don't give me the old bromide, "Well, everyone knows how to do this." Nope, It is not in my DNA, so a sentence included with the clip in the package would have saved me time and pain.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from WOODBURY, NJ
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When the door was in the closed position there was no power to the unit. The control panel buttons would not put the dishwasher in any cycle. the panel lights did not work.her
I first verified that there was 120 volt line voltage getting to the unit. I removed the outer door panel by removing the 10 torx screws located around the panel on the tub side of the door. Two of the screws are longer so note there location for reassembly. The door handle can now be removed. Pull the outer door panel away from the inner panel and remove the connector to the control board. Set the outer door aside. Remove the connector to the door latch.The latch is snapped in position at the top side. Pry using a screw driver to release. Snap new latch in position. Snap on connector, Reassemble door by first reconnecting the control panel connector. install plastic door handle. Mate door to inner panel. Note interlock tabs between outer door and inner panel near the bottom area. Install the 10 screws. The two longer screws are at the top holding the latch and handle.
Was this instruction helpful to you?
Thank you for voting!
Replacement of Top rack due to corrosion
The rack itself is rather easy to pull out, pop out the tabs and the rack will slide out. Once you get it out, its a bit more challenging as the rack itself needs to be disassembled. Don't waste a lot of time removing the rails - cut the tines on the old rack and take those off. Unscrew the back of the panel holding the adjustment assembly and the item will come off more quickly. All the rest of this is simple and can be disassembled and snapped back together by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SANDY, UT
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Dishwaster would not reliably start. Just blue flashing light
Removing the door was straightforward. However, when the door panel was removed, I grabbed the door and my finger touched and pressed on something on the right side. This is an optical collector which focuses 3 lights (red, blue, green) into a visible slot. After I reinstalled the door, the lights were not visible. I had to disassemble the door a few times and bend this optical collector into the right position. Basically, I bent the collector into the door, so I needed to bend the collector away from the door. And now, everything is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from CLOVIS, NM
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rack rail broken
Installed new rail and stop clip. Less than 5 minute fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from CHARLOTTE, NC
- Parts Used:
- WPW10350401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Upper Wheel Hub
1) Remove (2) dishwasher cabinetry (located on top or side) cap and screws.
2) Pull dishwasher out just far enough to access wheel tub assembly.
3) Remove old, clean area and replace with new.
“Refer to several videos buy goggling part number”.
2) Pull dishwasher out just far enough to access wheel tub assembly.
3) Remove old, clean area and replace with new.
“Refer to several videos buy goggling part number”.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from Morris, IL
- Parts Used:
- W10727426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
No instructions
Didn't work on it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from MADISONVILLE, KY
- Parts Used:
- 8193983
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn
Unscrew, replace, reacted
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from escondido, CA
- Parts Used:
- W10619006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch broke on dishwasher door
I removed the screws on the inside of the door. Removed panel from the outside. Disconnected the power wires to the panel. Disconnected the wires to the latch switch. Removed the latch assebly. Put new assembly in place. Connected swtich wire. Connected panel wire. Put panel back on dishwasher door. Installed panel retaining screws. Job Complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Auburn, NY
- Parts Used:
- 8193983
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spinner on top of Dishwasher fell off.
I loosened the one screw holding on the plastic that houses the tab that holds the spinner in place. Placed my finger between the plastic and pulled down slightly just enough to remove old tab. Place new tab which is small in the hole,you can actually feel it going in the right place. With your finger hold onto the tab and then snap spinner onto tab. Tighten screw back up. Make sure you cover bottom of dishwasher just in case the screw and new tab falls from your hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Meridian, ID
- Parts Used:
- 8193983
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Spinner Clip failed
The service video was great. This is a great product web site and service.... Thank you
Was this instruction helpful to you?
Thank you for voting!