66513932K014 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pooi from TORRANCE, CA
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper drawer rack stop clip broke caused one side fell off rail.
I followed the YouTube attached with PartSelect email invoice to fix it. I am very happy PartSelect sent repairing video instruction and took me less than 15 minutes to get it done. Awesome!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Galveston, TX
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing tine pivot
Pushed to be into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from CAMARILLO, CA
- Parts Used:
- WPW10350401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rollers wear out. This is the third set since it was new.
I removed the upper rack and unclipped the roller assembly and snapped the new ones in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Scottsdale, AZ
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A bracket was missing on the top rack of dishwasher
Easy. Part just snapped in and took all of about a minute. Now the top rack doe snot slide back and forth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LES from NORTH PORT, FL
- Parts Used:
- WPW10195623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic stop on front of drawer track broke off
1. Remove the top rack
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!
2. Take a screwdriver and pry off back plastic stop at end of track
3. Slide track off, then slide new track on
4. Take the plastic back stop originally pried off of old track and snap into new track
5. Open plastic stop at front of track
6. Replace top rack.
7. Close plastic stop at from of track
8. Good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from FORT COLLINS, CO
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
glide stop on upper dish rack broken
easy - plastic snap in part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Youngsville, LA
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Stops broke
Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from STATEN ISLAND, NY
- Parts Used:
- W10619006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door would not lock
Followed the u tube video. No problems. Will use them again.
Best recommendation I can give.
Best recommendation I can give.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from ALBANY, GA
- Parts Used:
- W10619006
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
door would not latch
We followed the video instructions, at times running to the computer to check the video.. The hardest part was getting the door to slide back on.. Thank heavens for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from REIDSVILLE, NC
- Parts Used:
- WPW10195623, WPW10195622
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Installing the rack stop clip was, at first, very difficult, if not impossible.
Stared at it and deduced that the clip was not intended to slide into the track from the end, but that it was intended to snap in from the side. NO WHERE WAS THERE A SINGLE SENTENCE TELLING HOW TO DO THIS. And don't give me the old bromide, "Well, everyone knows how to do this." Nope, It is not in my DNA, so a sentence included with the clip in the package would have saved me time and pain.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from WOODBURY, NJ
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When the door was in the closed position there was no power to the unit. The control panel buttons would not put the dishwasher in any cycle. the panel lights did not work.her
I first verified that there was 120 volt line voltage getting to the unit. I removed the outer door panel by removing the 10 torx screws located around the panel on the tub side of the door. Two of the screws are longer so note there location for reassembly. The door handle can now be removed. Pull the outer door panel away from the inner panel and remove the connector to the control board. Set the outer door aside. Remove the connector to the door latch.The latch is snapped in position at the top side. Pry using a screw driver to release. Snap new latch in position. Snap on connector, Reassemble door by first reconnecting the control panel connector. install plastic door handle. Mate door to inner panel. Note interlock tabs between outer door and inner panel near the bottom area. Install the 10 screws. The two longer screws are at the top holding the latch and handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from DREXEL HILL, PA
- Parts Used:
- W10619006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Top rack adjusters fell apart and would not slide back and forth.
I followed the Partselect video for the new installation. Very easy to follow which made new part installation extremely easy. Works perfect now!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria A. from CATONSVILLE, MD
- Parts Used:
- WPW10195622
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
End stop on the upper rack of the dishwasher
Reviewed the video of this problem. Followed these instructions using a flat screwdriver to release the broken stop. Then used the same tool to set the piece firmly in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from CINCINNATI, OH
- Parts Used:
- WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack stop clip broke
Popped the old clip out, replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSTOWN, PA
- Parts Used:
- 8193983
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spinner kept coming loose.
For easier access,removed both trays from dish washer. Pushed both clips apart from upper water arm, let arm hang, removed old spinner, replaced new spinner.
Was this instruction helpful to you?
Thank you for voting!