JDB9910AWS Jenn-Air Dishwasher - Instructions

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!

I just followed the instructions and all went well

Took rack out of box, son removed water tower from old rack, put it on new rack, rolled new rack into dishwasher. Presto! Done!

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

Ordered BOTH the front and rear tines as the front tine showed some superficial rust through the plastic covering in a couple of spots. Re-used the tine holders which were still solid condition and flexible. Snapped bowl holder tine unit out of dishwasher, snapped new tines in place, snapped unit back in dishwasher. Took 5 minutes or less. All other parts of the dishwasher rack were still in excellent condition with no cracked spots on the vinyl covering or rusted spots visible anwhere.

Just undid the brackets holding the top rack in place and put in the new racks, locked the brackets and in the bottom put the water tower on and slid that rack in place, and bam we were ready to turn it on. It's wonderful, all new and clean. LOVE IT!!!

unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

Turn off the power supply to the appliance. There is wiring you could mess up if something goes wrong. Open the door. Remove the four (4) torx head stainless steel screws on each side of the interior door panel. (total of 8). Then remove the two (2) torx head stainless steel screws near the top of the door on either side of the latch. Before you pry the interior door panel off, have handy a non-metallic weight, such as a brick or heavy book.. When you pull the interior door panel loose, the weight difference will cause the springs to pull the door up and closed. The brick will hold it open while you replace the cheap plastic handle. Do not try to fully removal the interior door panel as there are electrical wires attached. Just lien the interior door panel up onto the lower dish tray. You will need a 5/16" hex nut driver to remove the two (2) screws that hold the plastic handle on. Then, just reverse the whole process.

Snapped old ones off and snapped new ones on.

First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.

Unscrewed the dishwasher front panel. Took out the broken pieces of the handle and screwed in the new handle. Not hard at all. The website for the replacement part was easy to use & the part arrived quickly. Thanks

The most difficult part is learning how to unsnap the plastic retainers at each end of the steel sliders on each side of the dish rack. Push the end caps to the outside and the plastic inserts will snap open and slide off the ends of the rails in two pieces (note how they were oriented so you can replace them later). The caps must be removed from both ends of each rail. Slide out the basket. slide the rails out. Pull the old rollers off the pins. Place the new rollers into position. A smart rap with the palm of your hand should snap the rollers onto the pins. If you have done it correctly, the rollers will not pull off the mounting pins. You could also place a small block of wood against the roller and use your hand or a small hammer or weight to snap the pins into place. Assemble in reverse order.

Had service man: stated I would need new motor/pump at $400 complete. I didn't like the interior of new dishwashers. Nothing to lose, so I verified that the motor was working; reviewed short PartSelect video. Ref: very helpful PartSelect assembly diagrams with parts list. THANKS PS! Removed two dish racks (top rack: extend fully and flip the roller-keeper clips. Pull rollers and rack-pins apart) Then I started taking the pump apart all the way down to the pump base (fits into tub with seal - did not replace that seal). Very intuitive - some parts are tight and must be encouraged to come apart; take care of seals and o-rings; take notes of sequence if necessary. Look for parts requiring replacement. Unscrew Spray Tower Lower Extension Nozzle and lift off Spray Arm and two lower spray arm seals - check seals for wear. Unscrew pencil-like Spray Arm Support Nut. Cause: I found a totally-clogged Pump Housing Filter, a bit of steel wool about the size of my thumb (same size as water supply opening in bottom), and small piece of broken glass. Cleaned all parts coated with lime; new Pump Housing Filter (could not clean adequately). Cleaned the screens underside of filter support (difficult) with brush and wire. Replaced o-rings for Wash Impeller and Drain Impeller as a matter of principle. Only alignment requirement is with bottom water supplly hole. Everything works like new now! Recommendation: clean Pump Housing Filter annually.