Bissell Upright Vacuum Parts

Fix Number

FIX10270410

Manufacturer Part Number

B-203-1015

This is a Genuine OEM replacement part designed for use with Bissell Vacuums. This part is made out of Plastic. It consists of a Bracket/Roller and Plastic Wheels. Please note, Brushroll Assembly is Sold Separately. When replacing this part you will need to remove an Access Plate using a Screwdriver. Snap the roller into place, attach Brushroll Assembly and connect the belt to the spindle that turns the belt.

Fix Number

FIX10271956

Manufacturer Part Number

B-203-8161

Genuine Bissell replacement part, this item is sold individually. This Filter is a Pre-Filter, which means it will pick larger debris that the Vacuums pick up before it enters the main Filter. The main Filter will pick up the smaller particles and debris. The B-203-1192 Foam Filter can be washed with water and then left to dry before using it again. Do not use soap when washing this Filter, use water only.

Fix Number

FIX10272038

Manufacturer Part Number

B-210-1128

This is a genuine Bissell part used on steam vacuums. It features multiple spiraling rows of bristles. The brushroll is designed to agitate carpet and upholstery fibers in order to loosen debris. It fits into the very front of the base of the beneath the clear plastic base window. This part is sold individually.

Fix Number

FIX10270241

Manufacturer Part Number

B-200-0010

These are the right and left elevator levers for a variety of vacuum models. These levers are responsible for adjusting the height of the vacuum and its brush to suit different floor types, levels, and cleaning requirements. Crafted from high-quality OEM plastic, this pair of levers is sold individually and includes two levers and necessary springs. As these levers are made of plastic, they can break under excessive stress, use, or when clogged with dirt and debris. If broken, noticeable signs include difficulty in raising or lowering the vacuum, being stuck in place, or failure to pick up dirt effectively. To replace these levers, a Philips-head and flat-head screwdriver are all that is needed. Begin by carefully disassembling your vacuum, unscrewing the screws around the chassis, and removing the top to access its interior. Once the top portion is removed, unscrew and remove the motor cover or any obstructing part that blocks access to the lever(s). If necessary, remove the carry handle and/or brush roll to access the levers. The levers are located on each side of the vacuum interior and can be carefully removed by prying them out with a flathead screwdriver. Replace the levers, then reassemble the top portion, carry handle, and brush roll of the vacuum.

Fix Number

FIX10270572

Manufacturer Part Number

B-203-1267

Fix Number

FIX10270195

Manufacturer Part Number

B-160-1961

This is an authentic Bissell replacement part manufactured for use with upright vacuums and carpet cleaners. The belt is used as an actuator between the motor and brush roll. The belt drives the brush in a spinning motion to help lift dirt into the vacuum. Belts do wear out over time from normal use and need to be replaced occasionally. This belt is sold individually.

Fix Number

FIX10272331

Manufacturer Part Number

B-32074

Genuine Bissell replacement belts used on Vacuums. This is the Pack of Two (2) belts. Belts tend to stretch over time, so it is recommended to change them at least every 6 months for optimum performance.

Fix Number

FIX10272517

Manufacturer Part Number

BR-1007

This replacement belt is specially manufactured for Bissell upright vacuums. It is a genuine OEM part, not an aftermarket imitation. This belt is used to drive the brush roll assembly that helps to puck up dust and debris. It is recommended to replace these belts every 6 months to ensure optimum performance. Please note, this rubber belt is sold individually. To replace this item you will need a screwdriver.

★★★★★

★★★★★

1 Review

Fix Number

FIX10272369

Manufacturer Part Number

B-555-9113

This authentic OEM retainer assembly secures the left and right pivot arms of the brush roll assembly on your steam vacuum. The pivot arms allow the brushes to move and adjust to various surfaces for effective cleaning, and the retainer assembly ensures they stay in place during operation. The assembly comes with the necessary hardware for replacement and is typically located on the sides of the front base, beneath the plastic base window. If you notice that the pivot arms are loose or worn out, it is time to replace the assembly. To remove it, refer to your user manual to locate and access it at the base of your vacuum. Unthread the mounting screws and remove the old assembly from its housing, then proceed with installing the new assembly. Please remember that this includes both the left and right pivot arm retainers along with the necessary fasteners for installation.

Fix Number

FIX10270533

Manufacturer Part Number

B-203-1215

This part comes directly from the manufacturer. The Lever Filter is used in many models of Bissell vacuum cleaners. This Filter fits into Lock N Seal Lever (part number B-203-1190) and is used to filter out any large particles before the motor. This Filter is made of a flexible foam. This Filter should be replaced if it becomes torn or lost. To replace this part the Dirt Cup (B-203-2453) and the Filter Case (B-203-2454) will need to be removed.