Bissell Parts

Fix Number

FIX10270241

Manufacturer Part Number

B-200-0010

These are the right and left elevator levers for a variety of vacuum models. These levers are responsible for adjusting the height of the vacuum and its brush to suit different floor types, levels, and cleaning requirements. Crafted from high-quality OEM plastic, this pair of levers is sold individually and includes two levers and necessary springs. As these levers are made of plastic, they can break under excessive stress, use, or when clogged with dirt and debris. If broken, noticeable signs include difficulty in raising or lowering the vacuum, being stuck in place, or failure to pick up dirt effectively. To replace these levers, a Philips-head and flat-head screwdriver are all that is needed. Begin by carefully disassembling your vacuum, unscrewing the screws around the chassis, and removing the top to access its interior. Once the top portion is removed, unscrew and remove the motor cover or any obstructing part that blocks access to the lever(s). If necessary, remove the carry handle and/or brush roll to access the levers. The levers are located on each side of the vacuum interior and can be carefully removed by prying them out with a flathead screwdriver. Replace the levers, then reassemble the top portion, carry handle, and brush roll of the vacuum.

Fix Number

FIX10270195

Manufacturer Part Number

B-160-1961

This is an authentic Bissell replacement part manufactured for use with upright vacuums and carpet cleaners. The belt is used as an actuator between the motor and brush roll. The belt drives the brush in a spinning motion to help lift dirt into the vacuum. Belts do wear out over time from normal use and need to be replaced occasionally. This belt is sold individually.

Fix Number

FIX10270410

Manufacturer Part Number

B-203-1015

This is a Genuine OEM replacement part designed for use with Bissell Vacuums. This part is made out of Plastic. It consists of a Bracket/Roller and Plastic Wheels. Please note, Brushroll Assembly is Sold Separately. When replacing this part you will need to remove an Access Plate using a Screwdriver. Snap the roller into place, attach Brushroll Assembly and connect the belt to the spindle that turns the belt.

Fix Number

FIX10271887

Manufacturer Part Number

B-203-7898

Fix Number

FIX10271899

Manufacturer Part Number

B-203-7912

Fix Number

FIX10271453

Manufacturer Part Number

B-203-6761

This is an original Bissell part. This Solenoid Valve is used in many models of Bissell Carpet Cleaners. When powered, this valve allows the flow of water at the press of a button or the pull of a trigger. This part should be replaced when water will not flow or when it won't stop flowing. When replacing the Valve, double check the condition of the Tubing (part number B-203-6819) making sure that it is free of cracks and splits. Tools Used: • Philips Screw Driver • Needle Nose Pliers

Fix Number

FIX10271964

Manufacturer Part Number

B-203-8413

This is an authentic Bissell replacement part made for use with a steam mop. This is the cap and the insert assembly for the water tank. It is a specially designed item that will allow steam mop to access water in the tank. These items are made out of plastic material.

Fix Number

FIX10271956

Manufacturer Part Number

B-203-8161

Genuine Bissell replacement part, this item is sold individually. This Filter is a Pre-Filter, which means it will pick larger debris that the Vacuums pick up before it enters the main Filter. The main Filter will pick up the smaller particles and debris. The B-203-1192 Foam Filter can be washed with water and then left to dry before using it again. Do not use soap when washing this Filter, use water only.

Fix Number

FIX10271758

Manufacturer Part Number

B-203-7435

★★★★★

★★★★★

1 Review

Fix Number

FIX10272369

Manufacturer Part Number

B-555-9113

This authentic OEM retainer assembly secures the left and right pivot arms of the brush roll assembly on your steam vacuum. The pivot arms allow the brushes to move and adjust to various surfaces for effective cleaning, and the retainer assembly ensures they stay in place during operation. The assembly comes with the necessary hardware for replacement and is typically located on the sides of the front base, beneath the plastic base window. If you notice that the pivot arms are loose or worn out, it is time to replace the assembly. To remove it, refer to your user manual to locate and access it at the base of your vacuum. Unthread the mounting screws and remove the old assembly from its housing, then proceed with installing the new assembly. Please remember that this includes both the left and right pivot arm retainers along with the necessary fasteners for installation.