Blender Parts

Jar Collar - Left Thread

$8.30

Fix Number: FIX18268636
Manufacturer Part Number: 123662001000

This is the jar collar for a blender and is sold individually. This jar collar is left-threaded and is located at the base of the jar. No tools are required for this repair, as it can be twisted and secured by hand. This part is sourced directly from the manufacturer to ensure it fits perfectly with your appliance.

Blending Blade Sealing Ring

$6.51

Fix Number: FIX18273320
Manufacturer Part Number: 173916000000

This is the blending blade sealing ring for a blender. It seals the blending jar and blending base. If you notice leakage coming from the base of the jar, the seal is likely damaged and in need of a replacement. This is a common wear part on a blender, since the constant contact with liquid can gradually start to wear down a seal, however this is a quick and simple replacement. No need to worry if this sealing ring will fit your blender, as it is an OEM part, sourced right from the manufacturer.

Jar Assembly

$8.50

Fix Number: FIX17581586
Manufacturer Part Number: 990014500

Authentic Manufacturer Sourced replacement part used on some Hamilton Beach Blenders. This assembly includes a Plastic Jar, Blade Assembly and Bottom Coupling. Jar assembly locks into the blender base and holds the foods and liquids being blended.

Blender Seal

$8.70

Fix Number: FIX11757120
Manufacturer Part Number: WPW10686132

This is a replacement seal for your blender. The seal prevents leaking when you have contents in the blender. If your blender is leaking or is not properly connecting to the stand, you may have a damaged seal. This seal is approximately 3.5 inches in diameter and is sold individually. This is an OEM part sourced directly from the manufacturer.

Watch the install video

AGITATOR ASSEMBLY

$2.99

Fix Number: FIX19184418
Manufacturer Part Number: 31014904000

The 031014-104-000 Agitator is sold individually. The Agitator Assembly (Or Blade Assembly) is the part of the blender that chops, blends or mixes the product that is put into the blender jar. After time the blades will become dull or break or the spline that is attached to the shaft may wear out. When replacing the Agitator it is advisable to inspect the Sealing Ring, which is in between the agitator and the jar for cracks and if it has been compressed too much, which will cause it to leak from the bottom.

ROUND GLASS BLENDER JAR

$6.03

Fix Number: FIX19184156
Manufacturer Part Number: 124461000000

This is a genuine Oster replacement part, it is sold individually. This is the new round Jar design. If you have the old style Jar, you will need to order the part numbers, 124462-000-090 Jar Cover & 050613-002-089 Filler Cup.

Gasket

$6.51

★★★★★

1 Review

Fix Number: FIX10505574
Manufacturer Part Number: 006890

This gasket fits blenders and drink mixers. The gasket provides a tight seal between the blending assembly and blending jar to prevent liquids from leaking out when in use. If your gasket is worn out or your appliance begins leaking, then check the gasket and replace immediately. *Please note: this part is sold individually.

Washer

$6.51

★★★★★

1 Review

Fix Number: FIX10505518
Manufacturer Part Number: 003509

Genuine Waring replacement part, this item is sold individually. This part acts as a seal for the blenders shown below. It is installed along with other seals and washers underneath the cutter assembly, to prevent leaks from coming out of the bottom of the container. Over time these seals and washers will become brittle and compressed, then will have to be replaced.

Blender Foot

$8.70

Fix Number: FIX11747035
Manufacturer Part Number: WP9709707

Sold individually.

Fixes these symptoms

Touchpad does not respond
See more...

Installation Instructions

James from Shelby Twp, MI

Powers on monentarily at lowest speed. No other speeds work.

Primary problem was a bad speed control plate (SCP). I removed the rear cap exposing the speed control plate and pressed the adjustment screw while I changed speeds. It started working but saw sparking on the SCP contacts. Decided to first change out the worm gear & grease. 3 oz container of grease is avialable from Amazon. Don't buy the 1# pkg. You'll end up tossing most of it out. Contrary to other posts you must use food-safe grease, in case a leak develops, which was the case here. New control plate arrived damaged but the site replaced it promptly. Plate is labeled with wire colors but hard to read in dim light. Suggest drawing a diagram of the wire colors & placement before disconnecting. Also spent extra time adjusting the 3 screws on the plate so the mixer operated smoothly at all speeds. Rubber foot was much smaller & taller than the others and caused the mixer to rock slightly. Trimmed off the top and it worked fine. Read more...

Brush And Spring Assembly

$37.49

Fix Number: FIX10506937
Manufacturer Part Number: 027381

This is an authentic Waring replacement part, sourced from the original manufacturer for use with blenders. Brushes are items that will wear down over time and eventually need to be replaced. Worn brushes can cause the blender to run off and on, and can prevent the motor from starting all together. This brush is sold individually, please note two brushes are required.

Popular Blender Parts

Installation Instructions

Blender Brands

Related Blender Parts

Popular Blender Models

Blender Parts

Start With Your Model Number

Popular Blender Parts

Installation Instructions

Blender Brands

Related Blender Parts

Popular Blender Models