OEM KitchenAid Blender Parts & Accessories

Jar

$80.13

Fix Number: FIX11755858
Manufacturer Part Number: WPW10514649

This BPA-free plastic jar assembly holds up to 56 ounces and includes the jar, blade, and lid. It’s designed to replace damaged or leaking blender jars and features a secure locking base for stable blending. Installation is simple—just unplug the blender before replacing. Do not use with hot liquids or place in the microwave.

Installation Instructions

khalid from sarasota, FL

no problems

Direct fit Read more...

Blender Foot

$8.70

Fix Number: FIX11747035
Manufacturer Part Number: WP9709707

Sold individually.

Fixes these symptoms

Touchpad does not respond
See more...

Installation Instructions

James from Shelby Twp, MI

Powers on monentarily at lowest speed. No other speeds work.

Primary problem was a bad speed control plate (SCP). I removed the rear cap exposing the speed control plate and pressed the adjustment screw while I changed speeds. It started working but saw sparking on the SCP contacts. Decided to first change out the worm gear & grease. 3 oz container of grease is avialable from Amazon. Don't buy the 1# pkg. You'll end up tossing most of it out. Contrary to other posts you must use food-safe grease, in case a leak develops, which was the case here. New control plate arrived damaged but the site replaced it promptly. Plate is labeled with wire colors but hard to read in dim light. Suggest drawing a diagram of the wire colors & placement before disconnecting. Also spent extra time adjusting the 3 screws on the plate so the mixer operated smoothly at all speeds. Rubber foot was much smaller & taller than the others and caused the mixer to rock slightly. Trimmed off the top and it worked fine. Read more...

Mixer Coupling

$10.88

Fix Number: FIX11751771
Manufacturer Part Number: WPW10279256

This part sits on top of the motor.

Fixes these symptoms

Touchpad does not respond
See more...

Installation Instructions

MARGARET from Reston, VA

Replaced coupler

After watching several videos on YouTube to see how others have removed the coupler, either I don't have the 'finesse tap' that is required to spin the coupler clockwise faster than the motor in order to remove or it was just locked and stuck. I ended up taking the bottom off of the unit and using a vise grip secured to the screw on the bottom of the motor fan and a pair of channel locks on the old coupler. The unit was laying on its side so that the vise grip was holding the fan in place against the counter top. I easily grabbed the coupler with the channel locks as it was slightly raised from the base surface. I cranked the coupler with a clockwise turn and it came right off. I installed the new coupler in seconds which automatically tightened upon running the unit with the jar. I'm back in my morning smoothie business! I also replaced the jar as the male piece on the bottom was also worn out. For ~$30, I refurb'd my blender. Not bad!! Read more...

BEARING

$144.25

Fix Number: FIX12711832
Manufacturer Part Number: W11323429

A stiff or noisy blade assembly may result from a worn bearing, damaged seal, or loose mounting hardware. This service kit provides the bearing assembly, blade, acorn nut, O-ring, and washers needed to restore smooth rotation. First inspect the jar and motor coupling to rule out related damage. Match the kit to the full appliance model and correct jar design. Disconnect power before disassembly and protect your hands from the sharp blade. Reassemble each component in the proper sequence, verify that the shaft turns freely, and check the jar carefully for leaks before normal use.

Installation Instructions

Jim from Boulder, CO

Leaky bearing in the bottom of the jar

You sent me the wrong part - some electrical switch - not the bearing I ordered. I got a RFP and sent it back at my expense. I put instructions in the box to get me the correct part but was never contacted. You did credit me the item cost, but not the shipping cost in either direction. Your customer service does not answer the phone and the chat doesn't work either. You don't have customer service. I ordered the part from a competitor and all went well. You still owe me the shipping in both directions and I will do the unkind social media thing until I see the credit. I am in the legal business and charge $450 per hour. So far, I figure I am out well over $500 due to your nonexistent customer service. Read more...

Jar

$100.24

★★★★★

1 Review

Fix Number: FIX11756236
Manufacturer Part Number: WPW10555711

This genuine Whirlpool blender jar assembly (WPW10555711) is an ideal solution for your KitchenAid blender. The 56-ounce plastic jar includes blades, seals, and a drive spline, making it a comprehensive replacement part to keep your blender running smoothly. Before purchasing, check your blender's model number for compatibility.

Fixes these symptoms

Touchpad does not respond
See more...

Installation Instructions

Linda from Pewaukee, WI

Blade did not turn as well and small crack in plastic jar.

Just replaced it. Read more...

Watch the install video

Blender Blender Coupling

$14.16

★★★★★

14 Reviews

Fix Number: FIX11746921
Manufacturer Part Number: WP9704230

This genuine OEM drive coupling is used in your blender and attaches to the motor shaft in order to spin the blades. If your old coupling has become stripped or the teeth have cracked off, it should be replaced so that your blender runs properly. Remove the old coupling by using a flat blade screwdriver to pry it off. Use a cloth to wipe down the threads, ensuring there is no remaining debris. The new coupling has reverse threads, so it will be screwed on counterclockwise to the motor shaft. Please ensure that the appliance is unplugged before you begin any repairs.

Fixes these symptoms

Door won’t open or close
Touchpad does not respond
See more...

Installation Instructions

Sandra from Marion, OH

When I discovered the coupling on by blender was bad, I threw the blender in the trash. Several hours later I retrieved it thinking I should be able to fix it.

I looked up the needed part on this website and ordered it. It arrived a few days later. I pried off the old coupling with a screwdriver and screwed the new coupling on. The blender works great. Thanks! Read more...