OEM Wilton Band Saw Parts & Accessories

Bracket-support

$57.30

Fix Number: FIX10516512
Manufacturer Part Number: 5783411

This is an authentic OEM sourced part which is specially designed for use with Jet and Wilton band saws. It is an identical replacement for a missing or a faulty bracket-support that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. This high-quality bracket-support is made of durable metal and is sold individually, keep in mind the hardware to secure it is sold separately.

Guard-blade

$21.95

Fix Number: FIX10516480
Manufacturer Part Number: 5782831

This is an authentic OEM supplied part which is made for use with Jet and Wilton band saws. The purpose of it is to direct dust and debris away from the user as well as to provide protection for the blade. It is an identical replacement for a missing or a faulty guard-blade that was installed on a new unit. Please check the owners manual and the diagrams of your model for the exact location and the correct installation of this component. One durable guard is included.

Flat Washer, M8

$9.85

Fix Number: FIX10517157
Manufacturer Part Number: TS-1550061

This flat washer is designed to fit a variety of power tools. The washer helps distribute the pressure evenly between parts and has multiple applications depending on your specific tool. Check the diagram for the accurate location in your tool. *Please note: this part is sold individually.

Wheel Protector

$48.35

Fix Number: FIX10516474
Manufacturer Part Number: 5782691

This is an authentic replacement wheel tire for Wilton and Jet band saws. It is supplied directly from original equipment manufacturer and it is sold individually. Its purpose is to provide a stable grip for the saw blade. When attaching the new tire on a band saw wheel, it may appear too be too small, however it really is not. These tires when new are typically approximately two (2) or more inches shorter than the old tire. Tires are supposed to fit very tightly against the bad saw wheel. As the tire ages, the rubber hardens allowing for the blade to slip. Note, it is a good idea to put the new tire in hot/warm water to heat it up just enough to make it pliable enough to stretch. Its advised to have two people in the stretching process.

Table Insert

$17.55

Fix Number: FIX10516515
Manufacturer Part Number: 5783471

This item is a genuine part that has been sourced from the original manufacturer to be used with verticle bandsaws from Wilton and Jet. The durable plastic insert fits into the cap in the table where the blade passes through the table. The insert is used to reduce the gap around the blade in order to better support the material as it is being cut. Inserts wear down from normal use, and will eventually need to be replaced to maintain clean accurate cuts. This part is priced as a single item, please note tools may not be necessary to install the insert.

Carbide Guide

$74.30

Fix Number: FIX10385338
Manufacturer Part Number: HBS814GH-190-10

Blade Guide

$87.42

Fix Number: FIX10517168
Manufacturer Part Number: VBS1220A-132

This blade guide is supplied directly from the original equipment manufacturer. Sold individually, the metal blade guide is compatible with several band saw models. This component is fastened onto the lower blade guide lower support, ensuring accurate cuts on projects. A hex key and a screwdriver are helpful with the removal and replacement. Please refer to manual for further repair and safety instructions.

Flat Washer

$8.75

Fix Number: FIX10467627
Manufacturer Part Number: TS-1550031

This flat washer fits the following tools: saws, drills, planer jointers, and angle grinders. The washer helps prevent nuts and bolts from tearing or pulling through material because it creates a bearing surface. *Please note: This part is sold individually. Refer to the diagram provided by the manufacturer for installation instructions. Remember to unplug or turn off power on tool before beginning this installation.

Blade Guide-carbide

$48.35

Fix Number: FIX10516511
Manufacturer Part Number: 5783391

This part is an OEM from the Wilton manufacturer. The carbine blade guard is compatible with many band saw devices. The plastic item is fitted on each side of the saw head's support bracket, keeping the blade straight for cutting projects. A pair of pliers and a screwdriver may be helpful for making the repair. The carbine blade guard is sold individually.

Hex Nut

$35.15

Fix Number: FIX10467621
Manufacturer Part Number: TS-1540071

This is a hex nut for power tools. It is size M10, with a 1.5 thread pitch. This is the most common hexagonal fastener. It has internal threads that screw on to the shank of a hex cap screw, or a bolt.

Wilton Band Saw Parts

Popular Wilton Band Saw Parts

Wilton Band Saw Appliance Types

Related Wilton Band Saw Parts

Popular Wilton Band Saw Models

Wilton Band Saw Parts

Start With Your Model Number

Popular Wilton Band Saw Parts

Wilton Band Saw Appliance Types

Related Wilton Band Saw Parts

Popular Wilton Band Saw Models